Search results

trinity I am looking into doing that. Problem is you mod the connector and I don't know if I can reverse it.

Shoot. I replaced the speed sensor. Not a bad ordeal just jacking up the car was the worst of it. Still no luck. I pulled every fuse and they all look good. The cigarette lighter works so the speedcalc is getting power. Somebody said there was a red light on the speed calc but there isn't on...

The battery went dead and I charged it up. When I got the car rolling the speedometer does not work, the check engine light comes on, and the o/d off light starts flashing. I suspect a sensor burnt out or something equally frustrating. Any clues would be appreciated. mustang is a 97 GT with...

I am in the same boat you are but I don't know if it is as easy as just jacking up the motor a little. A lot of folks say go to the trouble of dropping the k member. It is time consuming but not near the frustration of trying to get to the bolts as the method outlined in the instructions given...

I am installing mac long tubes and catted H pipe on a 97 GT automatic convertible. My understanding is macs will install as is (no moving anything or cutting or welding) with an automatic transmission. If you need to remove the transmission you might have to loosen the passenger...

4.10 gears will get you moving and into the power curve better.

I should of asked about a cold air kit.

I am doing a pi head swap and put in comp 262h cams and bbk shorty headers. Any tricks or advise on how to deal with the oil stick tube while trying to install the driver head with the header attached? It was a real pain to get off and can just imagine how much fun it will be to put on with...

I went with tokico d-spec shocks and struts, vogtland springs, subframe connectors, metco lca, steeda uca, mm cc plates, steeda x2 balljoints and bumpsteer kit, poly front arm bushings. The springs are real nice and give a very slight additional drop on the front which looks mo better and...

How? It has a crank, alternator, water drive pulley. I have a convertible so I don't run the air much anyhow. I am about to install some Steeda U/D pulleys. I was in your same boat trying to decide between the yea and nay sayers but figured since I am staying N/A they do not hurt. Wouldn't...

What I did was remove the plug at the bottom of the transmission and jammed a big flat screwdriver into the teeth and kept it in place with channel locks. First time out with balanced puller I think I screwed up a little. Inside the pulley is a centerpiece like a big washer. I pulled that...

while I am getting informed what do the other marks 10 btdc and 30 btdc mean?

I am doing a head swap and an under drive pulley install to and want ideas on the best way to keep the engine from turning when I take off the crankshaft pulley bolt. I do not want to take off the starter because it looks like tight work I saw these alternate suggestions. Should either...

never mind. amazing what reading glasses do for bum eyes.

I have turned the booger round and round and I see nothing that looks like a notch. My dampner has 6 holes in it on the outside rim. Advise please. fast please if possible.

The throttle body is different so where the air connects is shaped different from a cobra and gt. If it is round it works for the GT.

Hummm. Reminds of the time we got the visiting city kid to pee on the electric fence. No I am convinced I should pass on this rodeo. Just idle ideas.

I agree but this is a gentlemanly theoretical discussion about the merits and the mechanics of porting plastic intakes. I declare Gangbanger the ace shooter. This idea is dead.

Now that is what I am talking about Gearbanger. That logic and info wounds the wild hare idea severely. Thank you. Still kicking though. I kind of agree it is a wasted effort and that gasket matching on the heads makes much more sense so the air isn't disrupted by the edge of the head...

Not surprised at that since working in plastics is not a mechanic or machine shop forte. Regardless of the material the intake is made of, gasket matching is beneficial. TRUE? The whole game is to present as smooth and unobtrusive path for the air to travel into the combustion chamber. The...