Search results

  1. stang_racer69

    1992 Mustang Coupe 5.0

    1992 Ford Mustang LX 5.0 Coupe (notchback) 101,695 original miles Manual Transmission Manual Windows Manual Locks Air Conditioning Second owner of this wonderful 1992 Mustang. I have owned this car for the past 11 years and have taken very good care of it as did the previous owner. This...
  2. stang_racer69

    92 Spark Plug Gap

    Whats the proper gap for a 92? My previous plugs were around .050 and I gapped the new ones at .045. I searched some online and found answers from .032 - .054
  3. stang_racer69

    1988 LX mustang 5.0 spark plugs

    Spark Plug Gap wrong thread
  4. stang_racer69

    Rear Suspension

    I'm going to have the boxes welded up before I throw some control arms in. Anyone running these?
  5. stang_racer69

    Rear Suspension

    Is anyone running the Jegster rear uppers and lowers? I took a look at them the other day in the showroom and they seem to be similar to other brands. Just wondering everyone's opinion on them.
  6. stang_racer69

    Transmission Bolt HELP!!!

    it would be the two holes in the bottom of the picture, the one on the electric outlet in the picture and the one to the left of it.
  7. stang_racer69

    Over heating!

    yup check for a head gasket leak, drain the oil and see if water is preasent. also, is there any air bubbles in the coolent?
  8. stang_racer69

    Transmission Bolt HELP!!!

    looking in this pic at the bottom of this thread it is the two bolts that would be in the very bottom of this plate http://forums.stangnet.com/showthread.php?t=621741&highlight=bell+housing+bolt
  9. stang_racer69

    Transmission Bolt HELP!!!

    I need the two bolts that go into the very bottom of the bell housing to bolt to the block. These are both missing out of my car, and Ford nor NAPA can look up the part number or size. This is on a 92 T-5 but I belive would be the same for any 87-93 Thanks guys
  10. stang_racer69

    Special Guest Appearance...

    I just came back too welcome back man
  11. stang_racer69

    Wheels & Tires

    I been away for a while but I am starting to work on the stang again. Looking to getting a set of drag lites and was wondering if I should go with a 26" or 28" tire. current mods are in the sig. also should i go 8 or 10" wide rim in the rear? thanks guys
  12. stang_racer69

    Starter Sugestions

    thanks 95 anyone have any experiance with this starter? any problems using my stock wiring becasue what they gave me is WAY WAY too short, what they supplied is only about 3' hardly enough to stretch around the motor then up to the silonoid on the drivers side fender well
  13. stang_racer69

    Starter Sugestions

    anyone???
  14. stang_racer69

    Starter Sugestions

    bump
  15. stang_racer69

    BBK vs FRPP shorty headers

    I picked up a set of motorsport headers a few years ago for $100, they are not the coated headers but neverless I couldn't pass up the deal. The fit perfect and hope when I remove them they fit just as good going back on. The only thing I dislike about them is that they have a coating of...
  16. stang_racer69

    Rate my planned combination...

    check out my sig. it is fun to drive altough it needs to be faster :flag: also I can get 18-20mpg if I stay out of it. I personaly would not hesitate to go with 4:10's on another car if I drove it everyday insted of my ranger
  17. stang_racer69

    Cobra Intake Install

    thats a GREAT tip, I'll have to rember that when I pull my upper off again, it was a :fuss: trying to get the gasket and manifolds lined back up
  18. stang_racer69

    Starter Sugestions

    if I have a stock T-5 tranny from a 92 is it 157 or 164 tooth? if it is 157 this starter would work then right? Why would you "have" to relocate the soiloniod?
  19. stang_racer69

    Quick header gasket question...

    I don't rember it making a difference when I installed mine