Search results

  1. z3r0c00l

    67 Coupe Roof is fiberglass . . .

    no problem. Actually, they had a product number for this panel but when I called they said it must have been a mistake. If you search their site today you can still find that the panel exists according to their catalog but alas it does not in reality.
  2. z3r0c00l

    67 Coupe Roof is fiberglass . . .

    awesome - sending PM now
  3. z3r0c00l

    Ford parts, 289 , 302, 351

    do you still have the 302?
  4. z3r0c00l

    67 Coupe Roof is fiberglass . . .

    Yeah, I just called and indeed they only sell the panel for the fastback. Bummer. Looking for a donor now. I agree that replacing is the best option. I've gone this far and put new metal all over and so leaving the roof as is would be ashame. mustangmutt: I need to fix my website. I have a few...
  5. z3r0c00l

    67 Coupe Roof is fiberglass . . .

    awesome. This is the last piece I need. All other areas have been replaced with new metal. I've been searching for some time now and thought I'd have to resort to chopping a donor car. Good to see that Dynacorn has begun to reproduce this panel. going to order in the morning. Thanks for...
  6. z3r0c00l

    67 Coupe Roof is fiberglass . . .

    I bought a 67 Mustang Coupe (with vinyl top) for the purpose of restoring as a daily driver. The roof panel is rusted through with several holes 1 inch in diameter or more in some spots. I expected some rust as the vinyl tops trap moisture, however I did not expect that the prior owner had...
  7. z3r0c00l

    Headers-for 289 302 351

    do you still have the headers for sale? I have a 289 - Believe these will still fit
  8. z3r0c00l

    Rebuilding Motor for 67 Mustang - Piston Question

    Yeah. I was actually a bit disappointed when I researched the block but as you say I may be able to bore it a bit more if needed. I figure I'll rebuild for now and build up a 289 while I drive the Mustang. I suspect I'll just do a re-ring for now and see how that holds up. It was...
  9. z3r0c00l

    Rebuilding Motor for 67 Mustang - Piston Question

    The cylinders all seem to average around 4.049 across and 4.0.59 top to bottom No ridge at the top of the cylinders. Seems like a lot of clearance.
  10. z3r0c00l

    Rebuilding Motor for 67 Mustang - Piston Question

    I'm rebuilding the motor in my 67 Mustang. I believe it's a 302 from 1978. The Block Casting is: D8VE 6015 A3A Z I measured the piston diameter which shows as 4.020 I was debating ordering new pistons and am wondering if I should go for +030 or just clean up the cylinders a bit and...
  11. z3r0c00l

    67 Mustang Electrical Problem

    Voltage Regulator - darn It was the Voltage Regulator. I had actually put two VR's in the car prior to starting this thread and so that's why I had not felt like the VR was the problem. Yesterday I went out and bought a new VR (Higher Quality) and what do you know? Blamo - no drain...
  12. z3r0c00l

    67 Mustang Electrical Problem

    Good stuff Thanks for all the replies - I'll try these suggestions and see if I can get this thing figured out. Again - thanks Patrick
  13. z3r0c00l

    67 Mustang Electrical Problem

    I have a 67 Mustang which I recently bought as a daily driver project. I now have the Mustang on the road (inspected and all) however I have an electrical problem where something is drawing about 3.3 amps draining the battery very quickly. My workaround is to disconnect the cables at this point...
  14. z3r0c00l

    Austin Mustang Club

    We just created a new site for the Austin Mustang Club located in Austin Texas. If you're located near Austin then come check out the new site and join the fun. http://www.austinmustangclub.com/ Regards, Patrick
  15. z3r0c00l

    Y2K Cobra R hood latch problem

    I'm going to try one more time to make some adjustments then it's off to the body shop. Thanks for the help.
  16. z3r0c00l

    Y2K Cobra R hood latch problem

    Yeah - I dropped the supports all the way. I may need to shim it more. I did shim it about 1/4 inch. I'll probably just take it to the shop and see what they come up with. Thanks though. pat
  17. z3r0c00l

    Y2K Cobra R hood latch problem

    I've installed my Y2K Cobra R hood on my 2002 GT and all seems to be lined up well; however the hood latch will not catch. No matter how much pressure I put on the hood. Gotta be careful how much pressure since it's fiberglass. Anyhow I've tried repositioning the latch and hood but still no...
  18. z3r0c00l

    Anyone have the link for the 06 order info?

    According to Brad's site: themustangsource.com the Bullitts may be a late offering. I'd still check with your Ford dealer to push for them if possible.
  19. z3r0c00l

    Anyone have the link for the 06 order info?

    Here you go: http://www.gotmustang.com/autoshow/2006_mustang_order_guide.pdf
  20. z3r0c00l

    Ghost Wheels for 2005 Mustang

    Man I like these ! I can't seem to find much info on their site about them so I contacted them and they sent me some pics. I have a few more pics if you want those posted. BBHills sells them http://www.bbhills.com