Search results

I have a 76 308, I am putting on some performers with 2.02 intake and 1.6 exhaust. My question is, how do I tell which piston I need? Like I said, it is a 308, 2.02 intake 1.6 exhaust, and forged is what I want (obviously) Any links to help, or direct links to pistons needed would be...

So can I just run a standard roation pump with the smooth Waterpump pulley? Will it slip or jump and not cool?

Right now my car has the routing simialar to 84.5 here http://mnmuscle.com/forum/showthread.php?t=74 But, I am switching to a car with a manual steering rack, and dont know how to run the belt? There is no AC or PS bracket, that is all going to be done away with, so what can i do? Can I...

My person experience is the cube is junk, they make a nice kit for it for about 60 bucks, but you have to buy it off a truck in most areas. Otherwise, just be crafty with a pliers.

Also, does anyone know what kind of power I would put down with the E7 set up and 10 pounds of boost with a 142cid B&M blower? All other happy bolt ons, headers and what not?

Cool, the motor is remanufactured. I am sure it has non forged flat tops, but like said, I do not know for sure, I will have to check when the time comes. So, if they are flat tops, should I go with forged? Forged flats or w/ releifs? And E7's?

What is the difference between the heads than? So I should port the heads that are on there and have the same outcome?

Well, I am buying a weiand blower for it, and I am curious what I should swap out to run 6-10# of boost. The motor has about 6,000 miles on the new long block. I was curious if I should just upgrade springs and rockers on the heads I have with a mild cam, or if I should switch to some E7 heads...

I have what I belive to be a stock 76-8 302(Mustang motor), do these have flat top pistons? How is Piston to Valve clearance? I want to put a mild cam in it and possibly a set of ported E7's i have sitting here, but I am curious if this is going to work or not? Should I just cam it and leave the...

Well, this is good, as most personal experiences seem to be not related to the tranny itself, and everything else is getting replaced.

I have had mostly autos, and I just got a T5 that I have not tore into yet. The problem is, the person I got it from said that at highway speeds, it had vibration, so assuming that this is only while it is in gear, and goes away in neutral, and is actually something in the tranny, what could...

Reserve capacity, so that would be 104 minutes.

Linkage, when you floor it, it is actually only quarter throttle...

I got a 1985 T5. The tag reads 13-52-162. The tail housing reads 13-52-066-919 The main housing reads 13-52-065-908 The main housing is also stamped with "Basic 1 A" Which year T5 do I have for rebuild, and is this a good T5 to build up with a slightly built motor? Thanks. I...

I have a hole in my hood, I am running the AIR GAP intake. Works good for me. Buy a cowl, they look cool anyways?

I always thought it was illegal under emissions to put a motor in the car other than what the vin says should be there. I also heard that is federal law for street vehicles, but I doubt that much. Brian

Just saw a commercial for bosch platinum 2's. what do you guys think of them? How about the platnium 4's? I am currently running standard NGK's. Brian.

Could be a few things, fan, water pump, etc. Your thermostat could have possibly failed closed?? Brian

Just put a 76 302 and C4 in my 92 vert, the motor should be about 170-180 horsies stock with about 300 pounds of tourque, hauls enough ass for me!! Hope this helps

Here we go again. So what are you trying to tell me, it will read the same as an AOD with whatever gear I purchase. EX. 21 tooth will read as acurate in the C4 as AOD?