Search results

Where does the guage actually hook up to? btw im a stupid kid tell me how hard it was when your done please

alright thanks for the advice, and the hope looks like i need a trip to the junkyard, i'll be ordering the headliner kit from 50resto, and i guess the 50$ switches :nonono: , and the steeda clutch cable kit oh and my exhaust is awesome i love it , it only gets loud if you kick it, yet at...

Well i need some parts and i need some advice 1. I need a clutch quad, cable, and firewall adjuster, what do you recomend and how do you install it? is it hard? how much would it cost to install all that? 2. my two switches (headlights & "starter" switch) on the left side of the dash have...

Today i unloaded some stuff from my hatch, and did the normal routine of slamming it a couple times in order to get it to latch but it didnt close. long story short we got the hatch to latch , although we did have to move around the striker and slam it over a dozen times, now my car won't...

are there any in the fort lauderdale area? I would love to just cruise from spot to spot with a bunch of sweet ass mustangs

I would move the battery back (if u haven't already) and get some subs and an amp lol personally i like your cars' stance, it sets it off

I got one, i have a relatively stock motor, I like it, it is easier on your leg, i got one because i thought my clutch was out and was the reason i had to grind in order to get into first and reverese, turns out i just needed a clutch cable/quadrant :( there goes 800 dollers

I have a Steeda 2" louvered cowl, i always have to be different :crazy: it was $400 it was in good condition all i did was wet sand it with 400 grit and then paint, didnt really see much weight savings though :( Click here to see my hood

i plan to keep my stock trans. and i'll hold off on the clutch cable and do you guys think i should get something like an aluminum flywheel instead of a tri ax? can a tri ax be installed without taking out the trans.? thanks for the help

I don't know very much about clutches but i know enough that it's a pain to install & i need one bad, so i'm planning on going by the local mustang shop to see how much they would install one for, how much does it normally cost to get a clutch installed? what clutch do you reccomend? should i...

if i had to do it over again, i would save up 2 grand and say the hell with it, so 2 grand if u want like a perfect job. :nice:

i like the sound of flowmasters too, but depending on my mood i usually like my MAGNAFLOW better, its not annoying when your actually inside the car driving but if you get out and walk behind your car it sounds amazing, and it gets loud when you want it to, although just driving around normally...

dont be stupid, just go with ceramic, or stainless would be even better. no questions asked

they are stock wires, i'm going to get new ones probably this weekend because im going out of town tonight (not in my car) they are on there as tight as i can get them, the only thing i can think that is wrong with it from what you guy;s have told me is either a funky vaccum line, a...

my spark plug wires all lead to the right plug, i just triple checked, could not gapping the spark plugs really cause all these problems? where are the vaccum lines that i should check? thanks alot , not only are your guys' advice helping me, its giving me some enthusiasm and stopping...

Thanks for the help, i'm going to go check to see if i put the wrong wire on the wrong plug, while my engine's cold, oh and to answer your questions no i did not take off the upper intake just the little plaque on top of it i did the whole driver side at one time then i did only two on...

I changed out my spark plugs because i thought it needed new ones, i labeled every stock sparkplug wire that i took off so i knew where to put it back on, i took off the old ones, and put in the new ones, except for two, because i ran out of time and none of the plugs didn't really need changing...

Whoops :nonono: sorry for starting a monsterous arguement, and then walk away from it lol Yes i know CF valve covers won't do smack on the track, but who cares! you'll be pulling in more asian babes! :D CASE CLOSED

Just so you know, Carbon fiber is lighter than aluminum. In racing lighter is better, so what's so "rice" about that? :shrug: I've been dying for a set of CF valve covers ever since i saw that v-10 in a penzoil magazine ad :drool:

my dad used his gun to spray and i'm not sure what brand model it is,for paint i used dupont imron, its supposed to be the toughest ***** out there :shrug: