Search results

Pair brand new ( in box ) silver Marvmot 17 x 10 silver pony wheels with center caps. Bought new from American muscle then changed mind and want 17 x 9. If you have 17 x 9 in xlnt shape will be willing to swap. [email protected]. Lake Isabella Ca.

Very good write up! I have two fox body's, one with a budget engine build (Explorer parts) and another with all the expensive high performance parts. Favorite is the budget build due to best bang for the buck performance.

GT40 Intake/Heads etc Not too bad. Think I paid about $150 for heads and intake and TB at pick a part. That included my labor to remove. Should have gone on 1/2 off day in the fall/winter as it was Aug in Houston and a steam bath. You may need to work on the heads too so keep that in mind.

Before you upgrade to disc in rear be sure to make note the motor trend test result comments below. This test does not take into account fade or wet braking to keep it in perspective. Braking performance from the Cobra's new four-wheel discs and 17-inch rubber was disappointing. Hampered by...

Car dies Had the same problem with car dieing. I had just bought a well used 1990 in Los Angeles and was driving to Houston through the Nevada desert when it just died going down Baker grade in 105 deg weather. Coasted to rest stop and began looking for problem and found nothing. After car...

Engine miss My mustang did this at 4000 RPM, looked all over for the problem and finally found the computer ground wire had way to much resistance. We replaced one of the 2 ground wires (#60 and #?) problem was gone. Good thing my son being an experienced master tech. Also Jrichter always...

trick flow heads The twisted wedge heads will use stock valve covers however in my car I did need used FRP aluminum rockers for the F cam so needed to remove splash gaurd on oil filler. I removed the larger valve covers when after removing phonlic 1" spacer. My son did the pushrods and...

Pony Boy, I am planning on putting the 1996 Explorer GT40 heads and intake maniforlds my stock 1990 5 spd GT hatch and noticed you have them in your sig. How much additional power did you feel/get for the upgrade? My 1990 car is bone stock (even removed the air silencer).

mount problem The energy suspension will not lift the engine as high as the prothane or stock rubber mounts. Could be just my car, I had to shim mounts to so steering rack did not hit passenger side of 7qt pan.

I do not want to blame the Eibach pro kit springs as do not know if that is the sole cause. Combination of adjustable upper lower control amrs with rod ends on the front side KYB adjustubles with most loose settings and maximum motorsport caster camber plate in front all contribute to ride...

Suspension springs Also have a stock 1990 GT Hatch and like the ride and has acceptable handling that goes with it. Even my son complained about the 1988 GT ride on the rough streets (and that suprised me). In 1968 did not buy a used 1965 GT350 and even then did not like the ride either...

Eibach pro kit I do not like the rough ride now. I am putting the stock springs back in. Not sure if it is all the springs since I have steeda full length sub frame connectors, adjustable rear tubular lower and upper control arms and MM caster camber plates. Car is tight on corner but hell...

CAM SURGE I have the same problem and have been trying to tune it out of the 140-1600 RPM range. Other than that the car runs and idles fine thanks to the tweecer. Please let me know if you find solution and I will do likewise. This has been going on for years. P.S. I use F-Cam and vacuum is...

245 50 16 I had 245 50 16 on my 1988. Did not like the lateral movement from side to side which affected handling. I bought 225/55 16 BF goodrich and no side to side movement. I do not have enough grab from a stop or in lower gears. I should go to 17" with 265 rear and 235 fronts. I do...

Overspray Thanks, my brother thought so as well.

Smog failure Try running regular gas it burns faster. Also check your air pump and lines going to heads and if applicable cats. Mine won't pass at 1500 and will at 2500 with ease which I believe is due to cam.

Probability of unibody damage is higher when car has been repainted to I will look harder if the overspray is not factory. My 1988 is black and cannot determine if any overspray is there. How about your's?

Overspray pic Attached is picture of overspray which does not appear factory.

Overspray No where else show paint except bottom. Not in door jam etc. Thanks

I intend to buy a 1989 mustang GT for over $4,500, red paint is in good condition considering sun damage to interior and body is really good with no apparent accidents. We looked at underside an saw some red overspray so am curios if it was factory overspray? The car has good carfax and no...