Search results

You wont have to worrie about air pockets, but i just take cap off start engine fill and wait till thermostat opens then fill and cap off..Done.

I would try to find out what ohm the stock 5.0 unit is and then go from there and no sorry i dont know what it would be..That way you can use your stock gauge.

I am pretty sure they are the same, i know Chevy is different from auto to manual. But i would call Ford and just ask.

Thanks for all your help man. Maybe it will run good. I hope.

I was always told that if it had XXX on it but spread out across the lifter valley it was called to **** block. Dont know why but thats i heard.

I am not sure which ones they are, my machine shop got them for me. They were pretty high, I paid $430.00 for them along with a $75.00 set of rings. I thought my machine shop was screwing me cause i look in summit and they had some speed pro forged for $350.00, but you say there are two kinds so...

Thats just it, the cam is screwed. Two of the journals were scared bad. And also these heads have 64cc chambers so my comp will proly be around 8.5 to 1. Thats an awful big chamber...i wish they were smaller. Do you think these heads are gonna make good power with my combo??

Thats what i thougth also, the cam that was in it when it had domes in it was a lunati 526,530, and the TFS1 is a 501,512 i think, so i figure i would need more, since the car ran pretty strong then as far as i can tell even though i never fellt all of it cause i pulled it apart to find a knock...

Alright guys I am ready to start assembly of my shortblock that had a cracked piston and just basically shot bottom end.. I am going with a flat top pistons with valve reliefs. I am using World Products windsor Sr heads. 200's. Ported cobra lower and stock cobra upper, and all the usuall bolt...

Hey guys, i have been havin a noise problem from my 89 coupe since i bought it.. Well i pulled rocker arms off and the pushrods out and soon noticed a problem one pushrod was stock length and all the others were longer!! WTF. Also all the long ones were slightly bent and the stock one was fine...

Well it sounds like you have Weld wheels. Mine do it do. There 2 piece and my guess is that the 2 pieces are rubbing together.

Thanks man, but i really want to know what the lash should be with a feeler gauge?

ttt

hey guys i just bought an 89 lx with a 306 with roush 200 heads and a 526/532 lunati cam. My question is that the roller rockers are very noisy so I pulled the valve covers to check and see whats going on, and well i found the following. The car has Erson 1.6 roller rockers, guide plates and...

Clean your mass air. Sometimes that helps. CRC makes a good mass air cleaner.

That is very strange, because I am having the same problem. Does your car have a tune in it or do you have a programmer, because mine has a diablo programmer and it seems to do it more often when you tune it differently. Please let me know something so we can both figure this out, because this...

I have an 03' GT with several mods, including a P-51 intake which I just installed last week. My question is that the car runs great going down the road and at wot but at idle I hear a huming noise coming from the center of the intake. The car Idles a little high and hangs a bit until I take the...

NItro I have a 03 GT that ran 8.5 in 1\8 and 13.4's in 1\4 with 4:10 gears and pulleys and cold air. I put a 100 shot NX wet kit on it and it went 7.79 in a 1\8 last weekend with terrible bottle pressure. So if I were you I would spay it, because it is the best hp per dollar. Definetly go wet...

I have a 03 gt with 61k on it, my problem is that the ses light is on for a cam sensor bank 1. I have replaced the sensor and it is still on. The car runs and drive great but sometimes when you start it, it will go dead or backfire through the exhaust and go dead. The car has pulleys,cai,intake...

Tranny My car is a 2003, I bought it new in late 02. At 12k the tranny started grinding third and fith gear. for replaced the whole trans. After the warranty ran out I broke three shift forks and three secronizers and two shift pads. Needless to say I thik you guys are correct when you say they...