Search results

$100 + shipping for the Nitrous Management unit, hoses, pressure gauge, and bottle brackets $50 + shipping for 10lb bottle This is a used kit but everything is still in good working condition. The bottle is practically brand new - has only been filled twice and still looks new. I am willing to...

$250 + shipping I'm returning my cobra to stock in order to sell it, so I'll no longer be needing this Borla exhaust. These pipes are in very good condition as you can see from the pic, and have a very nice distinctive sound. I'm not sure exactly what shipping will be, so if you're interested...

no i havent tried them yet, but i was hoping somebody knew where i could get one for a little cheaper. anybody else want to chime in?

so i need to replace the driver side rear brake caliper, one of the bolts things it moves on is frozen up. anybody know where i can get one cobra caliper?

when i was changing the clutch last week i noticed my tranny says tremec on it. im pretty sure ours are borg-warner but i was told tremec bought borg-warner at some point. the numbers on it are C2605803. i googled this and it brought up results for several different tremecs. is there any way to...

thanks for the quick replies guys

how did you guys remove the top pass side bolt on the tranny? im replacing the clutch and i dont see how this thing is coming off, it looks like the firewall is too close to allow a wrench even if the entire intake wasnt in the way. any suggestions?

i called around today and only 2 shops in my town will even install them. i took it to the first one and they didnt have a lift that lifted it on ramps (to preload suspension) and tried to tell me i didnt need to have the suspension loaded, so i left and went to the other and im getting them...

ok if its that easy ill just go ahead and paint them before i get them welded in

bump and another one if anybody is reading this- the instructions say i should paint them before the install to avoid rusting, but since theyre under the car i dont care how they look as long as they function. they are completely welded shut on both ends so no water can get inside so is it...

i got the mm full length sfc's in the mail today, im gonna take it to a shop tomorrow to get them welded in and just wanted to know how much to expect so i dont get ripped

very good site, thanks for the help pm sent

ok, one question. ive always heard pinging and detonation referred to separately, but from what im reading, knock, pinging, and detonation are all the same thing caused by spontaneous ignition outside the ignition front initiated by the spark plug due to compression and heat (in the compression...

good link 94-302-vert, ive read through it twice now and im just starting to get it haha. stanger007- ill hit you up for some datalogs when i think i have a general understanding of how it all works. i dont think i should have too much on my plate for an n/a tune with just bolt-ons, but i...

im thinking about saving up for a tweecer r/t and would like to know some good reading to get started. i think its something id like to get into and learn more about. so whats a good place to do some reading so i have some knowledge to start with if i do get it?

if you have the time i would consider doing a bit of wiring hiding; i would just want to show off that sexy engine as much as possible, i think as a buyer it would be more appealing cleaned up a little and its not but a few hours work :shrug:. not saying anything bad at all, i would just want to...

thanks for the help blksn955.0 basically after talking to a couple fellow gearheads they are under the impression that i could be (and probably am) pinging/knocking without knowing it. neither of them have experience running nitrous (one has a big turbo dsm and the other a bolton ls1), but i...

the main reason i want to datalog is to make sure everything is running safely with the nitrous (eg no pinging, knock, safe timing, etc). with some datalogging software, as i understand it, i would be able to make a few pulls, and if everything is ok i have the peace of mind and if not i have...

i thought about a tweecer/pms but i really dont have that kind of money right now, and i dont know anything about in-depth tuning like those require. that being said, since both of our cars are obd1 would his program work on my car?

anybody know a good program i can use for some datalogging? my roommate has a dsm and some program on his pda he can hook up for datalogging, but his is obd1 so im gonna need something for obd2 (right?). im just gonna be using it to make sure everythings running right with the nitrous so i know...