carb

  1. D

    Carb Spitting

    Hey, I'm looking for some tips after rebuilding my holley double pumper. When I stomp on the pedal (idling) the car will sputter and if I press moderately it will spit fire out the primary and air out the secondary. If I press the gas gradually, there's no issues and it revs as expected. It...
  2. 1

    1995 CARB CONVERSION CRANKING ISSUE.

    Hey guys, new to the forum. Ive followed this forum for 2 years without making a account and have always been able to find useful information however, this time I need more in depth help. Im carburetor swapping my 1995 gt and i have the carb mounted, intake swapped, fuel pump deleted in the...
  3. J

    1972 Mach 1 wont go above 4k rpm

    So I’ve dreaded doing this for a while because I’ve searched far and wide for answers and I’m still left with the same problem. I have a ‘72 Ford Mustang Mach 1, i bought it with a 2v headed Cleveland, FMX, and a 8in rear. It is a true Q-code car so it is supposed to be a 4V cleveland, with a C6...
  4. R

    Carburetor for 93 2.3L non turbo

    Hey everyone, I am doing a EFI to carb swap on my 93' 2.3L and was wondering what a good carb would be for this application. My distributor and coil are ordered and on their way so all I need is the carb. My budget for one is around $150-$200 any help would be massively appreciated. Thanks! ( I...
  5. T

    2.3 To 5.0 Wiring Questions

    I have the majority of the wiring done (I think) I used a duraspark ignition module. Have a ignition harness with it too. Got everything hooked up (coil, dizzy, module) and there's a few extra wires that don't go to any connectors. One of them is pink coming from the igntion coil positive...
  6. T

    Carb 302 Ignition Wiring

    I have everything wired up (starter, alternator, ignition). But coming off the positive side ignition coil terminal is a pink wire. Where does this connect to? There also a white, red, and yellow wire that aren't going to anything but coming from the igntion module. Any help?
  7. T

    (carb Wiring)do I Need A Distributor Rotor To Blaster Coil Wire?

    I have the whole duraspark ignition module and wiring. I have the 3 wires that run from the dizzy to ignition harness but do I need a wire that runs from the center of the distributor rotor to the top of the ignition blaster style coil? If I do need it where do I get one? Cant seem to find one...
  8. S

    Carb Fuel System Help

    Building a 393w to put into a 1995 gt. Sumped stock tank Air gap intake Alluminum heads Manual trans 750 and 830 holley double pumper (So i can choose from either) Hydraulic roller cam 240/248 @.050 on a 107 lsa I am thinking about getting a carter p4594 pump 72 gph with -8an line from tank to...
  9. GoldenEagle91

    Fuel Fuel Line Help

    hello everyone, I've been having recurring fuel leaks back by the tank on my 94. It's a carb swapped 302 with a Holley mighty mite fuel pump. I am using a combo of the stock fuel injection fuel lines and rubber hose to feed fuel to the carb up front. Last night I had a pretty bad leak that...
  10. DrakeRobinson68

    Hello From Ca With A '68 In Progress

    Hello! My dad and I are working on getting our 1968 inline 6 back up and running. I received the car in '08 but after a lot of life happened this project has been on the back burner. WE are starting to get back into it and it should be up and running by the end of the year. Currently it is in...
  11. DrakeRobinson68

    Engine 1968 Inline 6 Carb

    Hi, I have been looking everywhere for the right carburetor for my 1968 I6 Mustang. I found a re-manufactured one on summit racing (link) that says it is compatible but I am a little apprehensive buying it as the photo appears slightly different than the one that is currently on the car now...
  12. Nick Bos

    1970 Mustang 302-2v Carb?

    Hello all, Im wanting to rebuild my 2 barrel carburetor on my 1970 mustang coupe with a 302-2V. I'm having trouble identifying the carb. On the carb it says it's a motor craft and it looks like the original. But I'm not sure if it's an Autolite 2100 or a Motorcrafr 2150 carb. Do the rebuild...
  13. B

    79 Carb To Efi?

    Hello I need help on deciding if I should get this 79 foxbody. It's a 79 coupe with a 90s front clip and interior conversion. The guy that has it, had a 302 carburated and 5 speed t5 in it but pulled motor and tranny to put in his truck. My buddy has a whole 94 gt car that he will sell me and...
  14. Nathaniel Donnelly

    Stalling At Stop Signs - Dropping Cool Points On Campus

    Hi all! Just put a new distributer in, and my '67 Vert runs super-smooth! However, when I take my foot off the gas, the idle drops so low that I stall most of the time - especially at stop signs. Is this more than likely just a simple idle adjustment on the carb? I'm hesitant to change...
  15. GoldenEagle91

    Engine Correct Throttle Cable For Carb'd 94?

    Hi everyone, I referenced the thread on here regarding what is necessary for converting a fuel injected 94 Mustang with a 302 to a carbureted setup (see here 94-95 CARB SET-UP HELP!!!! | Mustang Forums at StangNet ). They mention that a throttle cable from a 79-85 work best (years that carbs...
  16. GoldenEagle91

    Electrical Gauge Wiring Of 94 Carbed Mustang

    Hi guys, I've been working on an engine for the last few years and finally got the engine dropped into place in the 94 Mustang I picked up. Originally the engine was going to go into a 79 Mustang Ghia but unfortunately that vehicle was stolen from me so a few things will be slightly different...
  17. LJ Barber

    Question About Carb On 66 Mustang

    Hello, I recently purchased a 1966 mustang 200i coupe. I had the intentions of restoring it with my father however my father had some medical issues and now for the most part I am left restoring it on my own. I have very little experience working on cars but i am trying to learn. I have a...
  18. Daddys girls GT's

    SN95 New 5.0 Car Build Bogs At Hit Of Throttle

    Guys I need some help! Just finished a 306 build with big heads, equal length headers, single plane intake, .554 cam and a Holley 750 ultra street carb. Runs great after 2500rpm but bogs at the hit. Bogs with a 1700rpm power brake and a 2300rpm trans brake launch. I adjusted carb and timing...