driveshaft

1996 Mustang Cobra SVT 5 speed manual, all stock except 4:10 gears, bassani x pipe and flowmaster mufflers on Eibach lowering springs. I removed my driveshaft, took it to a local driveshaft shop and they replaced the u-joints and re-balanced the driveshaft. I put it back on and now I have...

Been wanting to do a T56 Magnum XL swap for the past year or so in my 2006 GT, and I think I'm gonna pull the trigger finally. I've found everything I need except for the driveshaft. Driveshaft Shop is like 2 months out on all orders. Shaftmasters is another option, but they are confusing. They...

A little background first...a little over a month ago I installed the steeda tri-ax shifter on my 2014 GT. It was fine at first but then recently, the shifter started feeling sloppier and a few times, it went into reverse when I was trying to put it in first gear. I took console out and it...

Just recently bought another fox and I noticed that on the highway at high speeds above 65mph there is some vibration. I will say, though, it needs new tires - they’re bald. Anyways I got up under the car to inspect my u-joints and they look good, but I noticed when I spin the driveshaft and...

Hey guys :), really looking to get to the bottom of this... I had taken my car to my local Gerald's who do good work. And they checked my entire front end. Called me and said that the passenger outer tie rod was shot, driver inner tie rod shot, bushings for my front suspension shot, front/rear...

I just did an automatic to t5 swap on my 2001 mustang 3.8. I got all the way done and then the yoke on the driveshaft will only go in about 1". the new trans is from a 97 or 98 mustang 3.8. does anybody know if the yoke is different between the older or the manual mustangs?

Hey all! I'm getting a progressively worse vibration coupled with a bit of morning sickness on my '67 vert. It currently has a C-4 trans. Now that I have to fix all this, I've decided I want to upgrade the entire drivetrain, beginning with an AOD trans, new drive shaft, and LSD. I may or may...

Hi I have a 2001 3.8L Ford Mustang first 9 of vin 1FAFP4047 I was wondering what I could do in the rear end to safely increase my top speed I heard that the driveshafts are only rated for 120 and under or they explode what else should I replace that can’t handle 140 also what differential do I...

I originally bought this to put into my fox but my plans have changed. T56 with upgraded with a 26spline input shaft and a B&M shifter. Centerforce 26spline clutch included, looks to be in excellent shape, also come with a steel 8 bolt flywheel that may need resurfaced. Original aluminum 03...

Hello, I've been researching the T56 swap I'm piecing together for my auto 5.0 '92 and have been unable to get a clear answer on this. What is the proper length driveshaft to use for an 03-04 Cobra T56? I've narrowed it down to shortening a foxbody-spec driveshaft by 1.5 or 2". Does anybody...

Sold

I have a 90 foxbody and i have a driveline vibration. I was wondering if i got the aluminum driveshaft would it be able to stand my hp. I dont have anything special now around 280 but i plan on doing engine stuff in a couple of months and i dont want to twist the driveshaft. Ive read a bunch on...

This part under my GT is lose and shaking like hell.... I can't figure out whats the name of it and what needs to be replace. -Thanks in Advance for the Help.!

I have a '67 vert 2v 289 with a C4. Engine was just rebuilt 5k miles ago, and runs great at slow speeds. However, once I get above 50 mph or so, the car begins to shake violently, but not always. Sometimes it's as smooth as an Audi. When it does shake, I can really feel it when I put...