turbo

  1. mclang

    2006 Mustang GT Turbo Build - Megasquirt?

    Hi all. This is my first post to the forum. I did try searching for old posts to answer my question.. But could not find anything after a few minutes. I purchased a turbo kit for my 2006 Mustang GT. I would like to go the Megasquirt route for tuning if possible. I have a friend who does MS...
  2. D

    96 GT On3 turbo kit part suggestions

    So I plan on putting the On3 turbo on my gt and I am trying to get 400hp on it. I was wondering what parts I would need to get or that would be smart to get. I already know that the stock rods and pistons tend to go out around 400-450hp and I plan on buying them but I don't know what sizing...
  3. jeannelle101

    Best block / parts for Turbo build

    Hey guys, I was in the final stages of putting an on3 turbo kit on my 04 mustang GT. Then a leakdown and compression test showed that I have some pretty bad rings in cylinders 3 and 6. So instead of tuning I want to build the engine. My goal is somewhere around 800whp. I want to keep it...
  4. C

    For Sale 1986 SVO Mustang - Tallahassee, FL

    $3800obo For sale is a 1986 SVO Mustang. Ford churned out ~9800 of them over 3 years, each one had a 2.3L turbocharged 4 cylinder and 5 speed manual transmission. These rare cars were meant to compete with the Porsche 944, and this one is 1 of 388 Dark Metallic cars. Good: -runs and drives...
  5. R

    For Sale 2000 Mustang Turbo 6 speed

    Selling my 2000 GT. Car is located in Kent Ohio. Motor was just put together about 1700 miles ago by Victory Engines and CRT performance in Norwalk about 1 1/2 years ago. Just put 6 speed in the car asking $21,500. I can be reached at 330-815-9719. MOTOR Teksid block .020over Forged cobra...
  6. S

    What's it Worth? 2007 GT Premium Modified

    2007 GT Premium. Full Kenny Brown chassis & suspension mods, twin turbo, 37,XXX miles What's it worth
  7. F

    LS Swap New Edge Saleen S-281

    Hey there, fairly new here, figured I post my current project 2000 Saleen Mustang S-281 SC, bought the car with no engine. Kind of a Frankenstein of a build and a huge learning curve, so here is some info in case anyone is doing something similar. 5.3 LS swap, LS6 intake, PAC 1218 valve...
  8. paddyrk

    Fuel E85 conversion necessities

    I have a 1991 5.0 LX, with a 347 stroker swap making 325 whp with a manual valve body aod. I have plans to go turbo with the same internals as I had for NA (yes they can support my power goals), ~10.5:1 compression, and I want ~450whp, I'll only need a couple pounds of boost, but I want to see...
  9. R

    Stock crank limit numbers?

    So I've read everywhere that the stock internals will be teetering with death around 450hp, the only thing I'm wondering is the 450 to the crank or the wheels? I'm ordering a on3 kit at tax time and am unsure about the hp numbers I was thinking about running enough boost to hit 400 hp but if its...
  10. C

    For Sale 1988 Turbocharged 5.0, $6,400, Wichita Falls, TX area

    Solid car that needs someone who would like a Turbocharged 5.0. Would also be a great Christmas present for a father to give to his son as a bonding project car. The original Hurricane wheels with tires on them, two new tires that have never been mounted, some drag springs and other various...
  11. Schnelly

    What next? 2008 GT Project

    Buy the car - Check Install K&N Cold Air Intake - Check Install Tune - Check Install 3.73 Gears - Check Install Hurst Short Throw shift - Check whats next?
  12. Fox5-0

    For Sale HKS Bypass Valve

    Selling my HKS Adjustable Bypass Valve from my old setup. Great condition, comes with upgraded spring to support 12-18lbs boost. Also works great for vehicles with less than 12lbs boost. Used with Vortech pipe. Standard mounting base. $225 shipped OBO (816)977-5047
  13. B

    Engine Bobby wants to fix his turbo car

    I just bought a 90 mustang GT,5.0, automatic with a turbo. I noticed the exhaust and fuel system has been upgraded. I also noticed a vent line not on there. I'm not sure if it's because of turbo or just was left off. This car is very clean and very fast. I also need to do a head gasket job on...
  14. T

    ON3 turbo boost help!?

    Hello all, I have been trying to figure this boost problem out for a year now... I have the on 3 performance 76m turbo kit and I am only making 8 lbs of boost with springs set for 18+... I have removed and blocked the wastegate and still no extra boost. I did a boost leak test and only found...
  15. Modular2v

    SOLD On3 76mm for sale

    Ball bearing On3 76mm. Only has 4k miles on it. $300 obo. It came off my 2003 mustang gt on3 forward facing kit. I am located in Oklahoma City (73120)
  16. T

    Forced Induction Prep

    Looking for a list of components I should beef up before installing a turbo or supercharger. i.e. top end kits, rotating assembly kits, and any links or specs on how big the pistons need to be, bore, dish/flat, size of cams, etc. Thank you.
  17. Hellion2013

    For Sale 2013 Hellion Twin turbo Mustang GT

    Beautiful race red Mustang GT 6sp manual transmission with just 6800 miles! Car show and garage queen. Only driven on nice days. Hellion Twin Turbo system and other modifications which include 2- 62mm Precision ball bearing turbos 2- 44mm Turbosmart wastegates 2- Turbosmart Vee port by pass...
  18. 9

    Anyone turbo their 3.8 sn95 Mustang ? [build progress]

    This is the progress im at right now. I can add turbo #2 but the clutch cable and brake stuff is in the way of the downpipe. I will be adding hood air scoops. I'll probably do metal scoops. I need to cut a bit more for the air filter as well. Yeah, my hood's cracked. Hood pins are on the list also.
  19. wiseguyk

    Forced Induction New Engine And Turbo - First Start Questions

    Hey guys, I've been working the last month on installing a fresh Ford Racing 306 and On3 70mm turbo kit (among other things like painting the engine bay and wire tucking haha) and am getting close to having everything buttoned up. I've tried searching the forums but having no luck finding any...
  20. MoDriver

    SOLD Superchip For 2.3l Turbo Ford

    This posting is a high performance engine management computer chip primarily designed for use with 2.3 turbo Ford four cylinder applications using the PC1 calibration (see below for more details on application). This chip "piggybacks" the existing computer and optimizes full and part throttle...