Search results

  1. B

    engine management system

    anyone running engine management system in 5.0 with trickflow stage 2 cam and track heat intake? n/a motor Crane cams told me stage 2 cam is too big for eec-iv computer and needs engine management? Currently running stage 1 with street intake, looking to put stage 2 cam in with track heat...
  2. B

    Stage 2 trickflow cam

    I have a 91 Mustang 302 bored out to .030 (306) The rest of the block is stock except for the new probe pistons. It has the trickflow heads, stage 1 cam with the street intake. 24lb injectors, 73 mass air (C&L) 70 mm accufab tb, BBK cold air kit, 5 speed, eec-iv computer. N/A. Had a Programable...
  3. B

    Rear sway bar clearance with trick flow girdle cover

    Will the rear sway bar on a 1991 mustang fit with a trick flow girdle cover? Someone told me that it will hit the cover? Anyone using superior evolution axles for 28 splines?
  4. B

    Idle Problems

    I have a 91 Mustang Gt 5.0 that I just rebuilt. The block is bore out to 4.030 over (306). New probe 10:1 pistons , crank balanced and polished. Top end is Trick Flow street with aluminum heads and the stage 1 camshaft. Accufab 70 mm t/b with C&L 73 mm MAF. Holley afpr set to 40lbs with vacumn...
  5. B

    H/C/I & AOD to T-5 CONVERSION COMPLETE!!

    My winter project is finally complete after 3 months. 1991 5.0 bored out 4.030new trick flow (probe) pistons, 10.0:1 compression. Engine balanced and crank polished. New cam bearing, rings, bearings. Trick Flow Top-End Kit TFS-K514-360-350. Ford King Cobra clutch, new quadrant and cable and...
  6. B

    Trick Flow Upper Intake T/B Bolts (4)

    I'm changing the throttle body and spacer from my old stock Ford 5.0 upper intake manifold onto my new Tric Flow upper intake. The four studs that hold the throttle body and spacer from the stock unit are in bad condition from anti-freeze. Is the thread size the same on the Trick Flow as on the...
  7. B

    BACK UP LIGHT HARNESS?

    i JUST REMOVED EVERYTHING UNDER THE CAR FOR THE T-5 SWAP FROM THE AOD.I NOTICED THE NEW T-5 transmission HAS TWO SWITCHES ON IT. ONE ON THE FRONT LEFT HAND CORNER WITH A HARNESS ON IT ALREADY AND ONE BELOW IT WITH TWO PRONGS(PROBABLY FOR THE BACK UP LIGHTS). WHAT HARNESS DO I NEED TO HOOK UP...
  8. B

    Which Balancer should I use? 1991 5.0

    I'm rebuilding the bottom end of my 5.0 The crank is being polished and balanced and I have a new SFI Billet steel 50 oz flywheel ready to be bolted on. The crankshaft damper is original and is in bad shape, 125,000 + MILES. 1991 Mustang GT. Which crankshaft damper do you 5.0er's recommend? I'm...
  9. B

    REMOVING STEERING COLUMN

    How hard is it to remove the steering column from a 1991 GT. What is that cable alongside of the column on the right side? I also want to change the steering knuckle with a Flaming River Steering Joint and while I have the column out I might as well change it. Has anyone put one of these on...
  10. B

    Pedal Assembly Out!

    I removed the auto pedal assembly and now I am going to change the quandrant on the back of the new assembly. The two plastic factory ones come off right? Also what about the two large springs attached to the plastic quadrant? Do I still use them? Wasn't too hard getting assembly out...
  11. B

    Pedal change from AOD to stick

    I am ready to remove the last four bolts holding the steering column up in place. Will I have enough room after disconnecting the wire harness to lower the column and remove the brake assembly bracket and reinstall the clutch setup? I'm hoping it will clear the column. Thanks 1991 GT 5.0
  12. B

    Speedometer cable disconnect?

    How do you disconnect the speedo cable from the side of an AOD. I removed that clip that holds the cable into the housing, but that doesn't look right? Where is the speedo gear?Do you remove that side bolt and the whole assembly comes out?
  13. B

    YANK converters for AOD Tranny

    I am overhauling the AOD in my 91 5.0. Has anyone ever used "YANK" transmission converters?:shrug: (short for Yankee) From what I hear they are very good! But how much are they? Check out their web site: www.converter.cc
  14. B

    Should I use the phenolic spacer with trick flow intake

    Do I need to use the phenolic spacer with the trick flow intake. It does not come with the kit and which thickness? The part number i was looking at is TFS-51520008. 1" thick.:shrug:
  15. B

    Should I rebuild bottom end??

    I'm the original owner of a 1991 Mustang Gt with 125,000 miles. I replaced the headgaskets and had a valve job done on the stock heads at 100,000 mi.The car has been maintained regulary and does not smoke. I just purchased Trick Flow's Street Heat top end kit complete with their twisted wedge...
Top Bottom
Back
Forums
Menu