Search results

  1. H

    Tire Size 87 Gt

    Hello, I have the following question: Will a 225/50/R17 tire on a 8" wide rim in the front of 87 GT rub? The car is not lowered!! thanks Frank (Netherlands)
  2. H

    reading fault codes

    Hello, Can somebody tell me whats the best device for reading my computer fault codes of my mustang 1994. I have also a lincoln Navigator 1999 with some fault codes. Is it possible to read both cars with the same device???? allready thanks.....
  3. H

    C6 Transmission for dragracing

    Hello, I have a dragrace car that runs 10 low (a track in Holland). The car has the following specification: - mustang ‘67 - weight with driver 3550 pond - enigne 514 ci about 900 hp - camshaft (8000 rpm – redline 8500) - gears 3.91 - tire 26 inch. - 60 foot time 1.47 (without...
  4. H

    Automatic transmission

    Hello, We have rebuild a C4 Automatic transmission. Everythink is perfect except the reserve. When you put the car in reserve the transmission doesn't respond. But if you give the car a little throttle the transmission responds and gets in reserve!!! Can somebody tell me whats wrong...
  5. H

    clearance piston to wall

    hello, maby a stupid question.. If my piston has a diameter of 4.440 and the clearance thats needed is 0.0050 what is then the bore size !!!!! 4.445 or 4.460 greets Freek (from Holland)
  6. H

    rod bearing clearance

    Hello, I have a question about the rod bearing clearance. I have: - a 460 Siamese bore engine stroked to a 514ci. (0.080 overbore) - aluminium rods from manley - castrol R40 oil Can somebody tell me what the clearance should be of the rod bearing. Car is for dragrace...
  7. H

    Mass air problems

    Hello I have a 1987 mustang with a mass air conversion from Pro-flow (1992). The car runs not well at idle, its bump up and down +/- 100 rpm and smells like hell ...unburend feul. (If the engine is cold it runs perfect but after 5 min. it runs bad as discribed above) The follow thinks i...
  8. H

    O2 sensors and code 41 & 91

    Hello, I' have a problem with O2 sensors. When a dump the code of the computer i'am getting code 41 and 91. The cars runs rich and smels like hell (unburned feul). The follow thinks I have done to get rid of this problem: - new O2 sensors!! - measure all the wires....there were all OK...
  9. H

    wire O2 sensors

    hello, We have a problem with our mustang 5.0. If we dump the codes from the computer we get 41 and 91. We have bolt on new o2 sensors but we still get the codes 41 and 91. We have also measure the resistance between the ground from the computer and the sensor. And the resistance between the...
  10. H

    800rwhp on a foxbody

    hello, We from holland and have several foxbodies. We want to build a foxbody with 800rwhp!!! Can somebody tell us what we must do to get there.....or has somebody a current setup with 800rwhp money is no problem!!!!! greets from holland :nice: :nice:
  11. H

    stock gears mustang AOD 1987

    Does anybody know what the stock gears is of a mustang GT 5.0L 1987 AOD t-top thx
  12. H

    IAC and IAB

    What is de difference between the IAC and IAB ??? I was reading about this in an artical and i don't know the difference greets from holland
  13. H

    wheels for a 1987 gt

    hello, can somebody tell me of these wheels are looking good on a fox-body. I live in holland and must oder them from the states!! I anyone has a good sugestion for other wheels............ greets from holland
  14. H

    0-60mph stock 5.0L

    hello, how can tell me what the proformance of a 5.0L GT 1987 automatic is. I am looking fot the 1/4 mile time and the 0-60mph time thanks greets from holland
  15. H

    got code 98 on KOER test

    hello, can somebody tell me what de code 98 means on the KOER test:shrug: :shrug: greets
  16. H

    how much horsepower

    hello, Can anybody tell my how much horsepower my engine has!!! stock 5.0L (mustang 5.0L 1987) - BKK header 1 5/8" - 2,5" x-pipe - flowmaster with 2,5" tall pipes - timing 14 degrees - deleted smog pump - underdrive pully's - removed air silencer greets from Holland
  17. H

    getting code 44 en 94

    Hello, Yesterday i have install 2 new 02 sensors on my mustang because i getting code 41. With the new sensors on, i'am getting now code 44 an 94 on the KOER test (no code on the KOEO). I looked in de codebook and it's tell me that it has something to do with the air injection (smog...
  18. H

    ground o2 sensors

    hello, Can somebody tell me where the location of ground of the 02 sensors is!!! greets from holland
  19. H

    compression stock engine 5.0L

    hello, Somebody know the compression of a stock engine 5.0L (1987 mustang) greets
  20. H

    computer codes mustang 1987

    Hello, First of all sorry for my bad english, i'am from holland and write not very good english. I' have bought a mustang 1987 5.0L t-roof. It runs very well and i'ts has 78.000 miles on the clock. It has stand still for 12 years. The computer gives the codes 34 an 41. I have read that...
Top Bottom
Back
Forums
Menu