Search results

  1. E

    Expired Original 1969 Mach I Fmx Transmission

    Original 1969 Mach I FMX transmission with cross member, spacer plate, converter and drive shaft yoke. THis is a great core. I do know it did not work properly for the 400hp motor I had in front of it. $100.00 or Please make offer . Of course this is will not ship. Located in Cypress Texas.
  2. E

    1969 Glue in Window Channels Location

    Can anyone give me the dimensions from the front and back edge of the window to the edge of the Glue in channel?:shrug:
  3. E

    THE DEPTH OF A 1969 351W WP PULLEY

    :shrug:Can anyone tell me how deep the Water Pump pulley should be on 1969 351W 2bbl PS, AC, ALTN ?????????????:shrug::nonono: Also looking for a picture of a Pass side mounted timing pointer. Thanks
  4. E

    Grooooveee alignment ? 69 351W 2bbl

    :shrug::shrug:Can anyone tell me if the (2) grooves on the water pump pully are supposed to be lined up with the (2) grooves on the crank shaft pully. groove for groove? THis is a 69 351W w factory a/c :shrug:
  5. E

    69 Door handle Mech wrong?

    Hey, anyone seen this? new out of the blister pack. the mechanism is not the same. does this force me to different latch rods? These are from a well known name mfr. what gives man? :shrug:
  6. E

    69 door handles dont match?

    Hey, anyone seen this? new out of the blister pack. the mechanism is not the same. does this force me to different latch rods? These are from a well known name mfr. what gives man? :shrug: tried adding pic but unable:shrug::nonono:
  7. E

    69 Side scoop grills/grate available?

    Anyone know where I can get a set of the grills for the side scoops on a 69 Mach I? One wholesaler said they used ot carry them but they where to poor a quality to continue to offer them. Numerous requesdt have come back with nadda. Any suggestions:shrug:
  8. E

    Impossible to find? Power Brake Booster to firewall Bracket

    Hey all, I have been doing an exhausting search for the power brake booster braket that is sandwiched between the power brake booster and the firewall. I had a couple of good leads but they all fell through. I have made calls all over the country to find one of these with no luck. Apprently...
  9. E

    How far to go with Sound Deadening Opinions?

    Hey folks, I am installing the sound deadener/insulation, aluminum faced stick back stuff and was wondering how far to go inside the quarters, trunk quarters & outer tubs you would carry this? Looks like I have enough to complete but why chance it. :shrug:
  10. E

    69 Emer Brake Cable Lengths

    Anyone happen to know what the overall lengths of the factory cables for a 69 Mach I? disc/drum. LH factory is 32" and the replacement seems short by about 4". RH is long side but dont have the factory part to compare length. Checked the front brake cable bracket location and looks...
  11. E

    Overlapping Hushmat?

    Anyone know if you are supposed to overlap the sound deadener? How much of an overlap? 1/2" ? Do you basically shell the entire inside of the car? What about the structural parts where the trim mounts to? I would hate to have to remove any of the stuff. :shrug:
  12. E

    69 Emer Brk hole in Torque Box

    Hey folks, anyone able to give me a dimension from the fuel line tube to the center of the emergency brake cable hole? Torque boxes where replaced (surprise ! not) but the bodyshop neglected to put it in.
  13. E

    Gas Tank Sealant ~ 69 Mach I

    Can anyone recommend a sealant for the fuel tank to the body overlap? I am going to need just plain old seam sealer for some other parts of the car, think this is a good alternative?:shrug: or does it need to be more flexible?
  14. E

    1969 Mach I Power Brake Booster Extra stud

    Just tried fitting my new Power Brake Booster and noticed there are (5) studs on the boost. (4) long and one about a 1/2" long. Well...... there is no existing hole in the firewall to accept the short stud? Any ideas?
  15. E

    69Mach Fuel Line Routing and Clip location

    Ok, will try and splain this best I can. New SS fuel line from F-R. My question is how is this supposed to be routed under the rear Frame rail. Is it supposed to be tight against the rail/tub? Finess bend it in place? Next, front rail was not replaced but hole for clip has disappeared...
  16. E

    Parking Brake Lever 2A637 Passanger side

    Anyone know where to purchase these without overpaying?:shrug: This is the lever the parking/emergency brake attaches to which is behind the brake shoe. My "Body shop" guys lost it and claim they have no more parts of mine.......... :mad:
  17. E

    FUEL GAUGE WIRE HOLE IN A 1969 MACH I BODY

    :shrug:Can anyone provide a location for the fuel gauge wire in the body? This is where it exits the inside of the car drops down to connect to the sending unit. Im assuming the body shop forgot to put it in.:shrug:
  18. E

    RADIATOR SADDLES

    :shrug:Has anyone deleted the radiator saddles and just used the bolting to secure it? This is an aftermarket 3 core aluminum radiator and vertical adjustability is tight.:shrug:
  19. E

    SPRAY GUN PURCHASE

    :shrug:Hey Yall, Im looking for an inexpensive way to paint parts. I hate the idea of using cans. I heard of a HVLP made by Grizzly that could be a good option. The car is done and I am assembling it myself. Any suggestions would be great.:shrug:
  20. E

    1969 Connector Pigtails Available?

    :shrug:Anyone know if the Ignition SW, Wiper Sw, Lt Sw Connectors with Pigtails are available anywhere?:shrug:
Top Bottom
Back
Forums
Menu