Search results

  1. stang-geoff

    belt size or part# for ac, ps and smog delete

    I just want to run the alternator and water pump. I've seen lots of guys do this. Anyone know what belt they're using?
  2. stang-geoff

    checking pushord length with hydraulic lifters

    How do you guys check what length you need? I have the pushrod length checker tool but doesn't the lifter need some preload so would I need to buy pushrods a little longer than what I measured or would buying pushrods at the measurement I take be fine?
  3. stang-geoff

    TFS stage one cam has no keyway

    My new cam has no keyway. There's just a hole where one would be at. Is this right? How am I suppose to put this together? well apparently my old pin should be able to come out fairly easily. I tried yanking it out earlier. I guess I'll have to try again. managed to get that pin out with some...
  4. stang-geoff

    engine rebuild connecting rod clearance issues

    I'm rebuilding my 302 and I'm having some issues here. I bought new pistons and pressed them on the rods and now that I'm putting the motor back together I can't get 2 rods to fit on one journal.
  5. stang-geoff

    what valve springs do I need for my gt40ps

    I think I'm going to buy this cam with 1.6 rockers unless there is more to gain from stepping up to the next cam. Trick Flow Specialties TFS-51402000 - Trick Flow® Track Max® Hydraulic Roller Camshafts for Ford 5.0L - Overview - SummitRacing.com What valve springs do I get? I know there's...
  6. stang-geoff

    cam choices for stock gt40p head

    I just bought a set of gt40p heads today for my 86 mustang at a bargain! I'm wondering what cams are a good choice for the gt40p? Is it possible to keep the stock valvetrain and get something with better lift over stock? I know I have the flat top pistons and I'm going to get that addressed...
  7. stang-geoff

    My car is running very rich

    Like the title says, it's running rich. The car also misfires at idle and cruising. I hooked up a scope to look at my 02 sensors and both banks read the same. The sensors weren't switching at all. Both of them had the same readings. They're 3 wire sensors and I'm not sure which one is the...
  8. stang-geoff

    controlling aftermarket fuel pumps.

    I was wondering on these high flow fuel pumps does or has anyone used a rheostat or some other form of resistor to control the flow rate of the pump? I was thinking these high flow models on stock cars will create more evap emissions and heat up the gas more by continuously flowing excess...
  9. stang-geoff

    power cut almost completely under engine load

    I've about lost it with this car. It's getting frustrating to say the least. Anyways, I'm having some serious driveability problems. My car is having misfire problems and under engine load the power is completely gone. It's like it hits a brickwall and the car will not accelerate. Such as if...
  10. stang-geoff

    Is the 87-93 master cylinder a direct bolt on for an 86 mustang gt?

    I'm just wondering. I'm taking my car to my school's shop. I've been having serious braking problems and if we diagnose the problem to be the master cylinder I'd like to buy an 87-93 master cylinder since my shop uses a power bleeder that only works with the modern nylon/plastic reservoirs.
  11. stang-geoff

    GT-40 intake from a 98 explorer. EGR questions

    I just went to a junkyard today and pulled an intake off of an explorer. I'm confused. The explorer had the typical egr system you see on most late model fords, but the upper and lower intake manifold still have that little egr port that goes through the middle. Is it possible for the car to...
  12. stang-geoff

    Does my 86 GT have 4 cats?

    My car has the factory hpipe and it looks like it has 4 cats. Are there really 4 cats or are the back ones something else?
  13. stang-geoff

    turbocharging a speed density Mustang

    I was wondering if anyone has turbocharged a speed density 5.0. Would it be possible to remap the ecm with a moates system and function with a turbo? Would the map sensor still work fine under boost? I know systems like megasquirt work just fine with a map sensor under boost. How well would...
Top Bottom
Back
Forums
Menu