Search results

  1. mustang70

    Cold Start

    I'm finally getting down to the small details. The current one is the cold start. For the first start of the day the RPM will fluctuate a bit before settling down. I tried to get that in a log, but it was just a little too warm to hit that part of the WUE table I guess. Once it settles I can let...
  2. mustang70

    Model Engine Run by MS2

    Hopefully this link works. And I hope it's ok posting this here. I figured it went here since the description says its controlled by an MS2. Pretty impressive IMO. View: https://www.instagram.com/p/B9N-Rkang-S/?igshid=87vjy494jwr9
  3. mustang70

    And I'm Back

    After almost two months I finally got my ECU back from DIY. I put everything back together today and of course it doesn't seem to be working correctly. I swear I had this thing pretty dialed in before I sent the ECU off. So I have a couple quick questions. First is about the flex fuel sensor. I...
  4. mustang70

    Wheel Sensor

    I was just curious if anyone has managed to to a stock ABS sensor as a wheel speed sensor? From what I read in the manual it says it can use a magnetic pick-up, but it needs an interface. I think the interface would be easier than trying to add another sensor to the spindle. This would be for...
  5. mustang70

    MAF System

    Is anyone running their Megasquirt with a MAF set up? I've been toying with the idea of switching over to MAF since I still have everything in place. The MAF is just unplugged currently.
  6. mustang70

    Better way to adjust speedo?

    I noticed today my speedo is off about 5mph. The drive ratio was set to 3.27 so I changed it to 3.55. I also adjusted tire size to closer to the actual size. The speedo was still off. The reluctor wheel was set to 13.70 teeth. From what I found the T-56 has 12 teeth. Is it better to adjust that...
  7. mustang70

    MS3 Newbie

    I've recently made the switch to the MS3 PNP in my 04 Cobra. It's a pretty basic set up as far as a Whipple and return fuel system. My first question lies in the return fuel system. I currently still have the FPDM in place as I was using it to give the stock type prime before start up as opposed...
  8. mustang70

    Gasket matching

    Has anyone that has swapped the PI intake onto the non-PI heads gasket matched the heads to the intake? I saw a couple pics and it seems like it wouldn't be too bad. What I'm wondering is if there is enough metal around the port to do the matching or would I run into a water jacket?
  9. mustang70

    Speedo check....

    I had 3.73's installed today with the 23 tooth speedo gear. In 5th gear at 70mph I'm turning around 2200-2300rpms and at 80mph I'm turning 2600rpm. Does this sound right. I know I'm going to have to get used to hearing the engine at the higher rpms. It just felt like I was going slow and being...
  10. mustang70

    a/f ratio

    I've been looking at some other dyno graphs and noticed that the a/f ratio on the chart is usually pretty level. I looked at mine and it gradually moves to 11.7. It has a steady decline as the rpms go up. Is that normal or should I start looking into something? It still has the stock fpr and...
  11. mustang70

    Mid pipe gaskets

    Where can I get the exhaust gaskets that go between the manifolds and mid pipe? Can I get them at a place like Autozone or do I have to hit the dealer?
  12. mustang70

    Made it to the dyno finally

    What do you guys think?
  13. mustang70

    PI vs Bullitt

    I was wondering if there would be any power to gain with using a Bullitt intake over a PI intake when I swap my heads. I know for a stock N/A car there isn't much power to be gained, however, I'll be putting on a set of stage 2 heads from Steen and a pair of stage 2 cams from VT. Since I'll have...
  14. mustang70

    Abs

    Was ABS standard or optional on 98 GT's?
  15. mustang70

    4V vs 2V intakes

    What is the difference between the 4V and 2V as far as the intakes go? Are the head further apart or is it the port design?
  16. mustang70

    Daily Driver with cams

    Is anyone running the VT stage 2 cams in their daily driver? I'm looking at these cams as part of an upgrade and I'm wondering how they are day to day and running through traffic. I put about 30 miles a day on my car and sometimes get stuck in traffic. I don't want something that's going to make...
  17. mustang70

    Ford racing blower

    Has anyone used this blower or know someone that has? http://www.fordracingparts.com/parts/part_details.asp?PartKeyField=5066 I'm sure the performance isn't close to the Kenne Belle, but the price is pretty good. I think it gives around a 6psi boost. I'm just wondering who's had experience...
  18. mustang70

    Body dipping

    I was wondering if anyone has had the body of their car dipped in acid to get all the junk off? How much did it run? TIA.
  19. mustang70

    Smallest rim?

    What's the smallest diameter rim that will fit over the rear disc brakes? I'm looking at getting some drag radials for my car since I've decided I like going to the track. I was thinking of running a slightly smaller rim so I can run more sidewall for a little more flex. So will 15" rims fit or...
  20. mustang70

    Power shifting

    How many of you have to granny shift from 1st to 2nd? I've noticed when I power shift my back tires spin enough to make the rear end sway a little. I'm shifting at 5k since I've read anything higher is pointless. Should I wind it out a little more to stop the spin or just save up for tires? I...
Top Bottom
Back
Forums
Menu