Search results

  1. OonDeanisS

    Expired Stock '82 Non Roller 351w Parts

    i have the stock cam, rods and pistons. Located in Danbury, CT. $50 for cam and $100 for the rods/pistons.
  2. OonDeanisS

    Expired 87-93 Bbk Catted X Pipe For Lts

    i have a barely used x pipe with cats, for Long Tube headers, i only put a few hundred miles on it to pass emissions. Located in Danbury, CT. $300 obo.
  3. OonDeanisS

    Running No Cats?

    can i leave all the smog pump stuff intact and working and just vent the fresh air out the hose instead of into the cats? im thinking this should avoid any trouble that may arise from removing all the smog stuff. i dont want to run into running problems, and i just passed emissions clean as a...
  4. OonDeanisS

    I Need Some Help With My Electric Fan

    My electric fan used to work before I deleted my a/c, and now it won't kick on. It has it's own temp sensor. It works when supplied power, but it's supposed to kick On when the car hits 180 degrees. There are 4 wires to the fan. 2 red, one green, and one black. The green goes straight to...
  5. OonDeanisS

    Block Going To Machine Shop In The Am

    i know this is short notice, but im taking my 351w block to the local ford guy tomorrow morning to have him check it out and determine if its acceptable to use it for my build... im planning to stroke it to a 408. the block is from a 1982 truck, im not sure if it was a f-150 or f-250...
  6. OonDeanisS

    Fuel Rail Lines Question

    i broke the hard plastic fuel rail lines that connect to the hard metal lines on the passenger side of the engine bay, notices fuel leaking, so i cut them off the hard lines and removed the entire fuel rail system from my car. Is that somethign ill have to get from ford? they look like they...
  7. OonDeanisS

    Getting Ready To Pull My Motor... Tdc Question.

    I broke a head gasket between the #6 & #7 cylinders, causing a misfire and before i knew what the problem was, i revved the motor and (only at high rpms) i could hear a loud clacking noise from what seemed like it was inside the motor. At that time, i assumed i broke an internal part like a rod...
  8. OonDeanisS

    86 Gt Front Valence On An Aero Fox?

    I remember seeing this done once years ago, but i cant find it now... does anyone have any info on putting the lower half of an 86GT front bumper onto an aero car without swapping to 4eyes? Heres a photo of a quick sketch i made using the photo from a latemodelresto ad. Don't mind my drawing...
  9. OonDeanisS

    Catted Midpipe With Long Tubes And O2 Sensors

    does anyone know if i get a catted h-pipe for my long tubes, do i need to install the o2 sensors before or after the cats? does it matter? i need them to pass emissions by the end of this month. this is for a 1990 manual 5.0. thanks
  10. OonDeanisS

    cc plate install question

    i have hotchkis cc plates on my car. if i was to remove one, what would need to be done? can i just mark it and unbolt it no problems? or will the strut shoot me in the face?
  11. OonDeanisS

    NEED HELP FAST! re-pinning o2 harness... thanks

    i need to re-pin my o2 harness where the black wire loops the purple/yellow to the blue/yellow wire, but i cant figure out how to re-pin it. can someone please help me re-pin it? i am on a lift at work and i only have another half hour to get this done. sorry for the rush. thanks so much.
  12. OonDeanisS

    steering "loose" help please

    my car handles great on back-roads and on new stretches of highway, but on some uneven pavement, its really difficult to keep the car in a straight line. the curves in the road pull the car side to side VERY easily, and im not sure why? i swear people must look at me and think im drunk. I have...
  13. OonDeanisS

    steering "loose" anyone have an answer?

    edit: sorry, wrong category... moving to tech.
  14. OonDeanisS

    I just want to share some pics!

    title says it all. Hope you like it!
  15. OonDeanisS

    new o2 sensors, new harness, high idle??

    i just replaces my o2 sensors with ford racing parts from 50resto, and i replaced the harness they connect to with a unit from ebay (hold your applause), and now when i start the car, it goes up to 3100 RPMs and holds there. i can give it throttle, but it just comes back down to 3100. IF i...
  16. OonDeanisS

    EFFN april fools!

    damn stangnet, could you make this any more difficult for us?! not only is the whole forum pink and purple, but its all diagonal, and every time i move my mouse it bounces between straight and slanted, making it near impossible to click on anything! what a pita. april fools should be fun.
  17. OonDeanisS

    help with o2 sensor wires please

    i took my 02 sensor harness out of my 1990 5.0 manual trans. and re-wired the whole harness because it was full of short wires butt-connected all over the place, and i was getting a code for LH 02 sensor. so i made it nice how it should have been all along, but now im not sure what wires to...
  18. OonDeanisS

    is it a bad MAF?

    my car runs like crap- backfiring thru intake, running "flat" and losing power, and bouncing idle. I disconnected the MAF, and bingo! car runs like a champ! except it smokes and doesnt idle very well this way. I also smell fuel. But my question is this... will a new MAF make the car run like...
  19. OonDeanisS

    no code 11

    so i ran a KOEO and came up with 4, then 91, 31. no 11? I keep reading that this means i have "computer or wiring problems" but what does THAT mean? how can i fix this? any help greatly appreciated!
  20. OonDeanisS

    Auto lite 3924 doesn't fit?

    I have gt40 iron heads, and I bought auto lite 3924s but they don't thread in... They look identical to my old plugs but these won't thread into the hole... I don't get it. Do I need to cut off the aluminum washers or something? The old ones thread in and out fine, but those are NGK platinums...
Top Bottom
Back
Forums
Menu