Search results

  1. FastA$$89Vert

    bad sqealing sound from motor..

    I took my gt40 upper intake off last week to re seal the valve covers. Ever since I put it all back together im getting a loud squealing sound mostly at idle after it warms up. It will go away when you rev it and come back when the RPM's fall back down. Is this a vacuum leak? Could i have put...
  2. FastA$$89Vert

    Terrible Squealing Noise

    Theres a loud sqealing noise coming from the driver front of the car. It gets louded with higher RPM, I thought it was the belt, so I sprayed some dressing on it, but it didnt help at all. What else could this be? Loose pulley?
  3. FastA$$89Vert

    NOISY transmisson......

    I have a tremec 3550 5 spd, and when its in 5th on the highway, its really loud It sounds like metal bouncing around and the sound comes right fromt the shifter. Any ideas? Thanks
  4. FastA$$89Vert

    Clutch got REAL soft, WONT WORK

    Clutch has been in for over 2 years, just put the top of the motor back together, clutch was fine, all of a sudden it went soft, wont work at all now, cant even get it into gear. What could this be???? Someone said the pressure plate may have collapsed.
  5. FastA$$89Vert

    Which Blower?

    I am posting this here because its a lot more active than the power adder section. Which blower do you reccomend for a 5.0 Im thinking of selling the nitrous and going to blower. Ford Racing makes one with 6-9 psi for 1799, How good are they?
  6. FastA$$89Vert

    Put motor back together...WONT START

    I just got the motor back together and now it wont start. Fuel pump is turning on, spark is gettin to the coil, firing order is right, but it just cranks with no effort to start at all. ANd it will backfire now and then. i have a new cap and rotor, still no luck
  7. FastA$$89Vert

    How do I prime the motor

    I just put my motor back together after 9 months of it sitting around. How do I go about priming it. Thanks
  8. FastA$$89Vert

    Is my block ruined? *PICS*

    I let my car sit outside for about 9 months with the motor apart down to the block, hood closed and a sheet over the block...is my block ruined now? This is what it lookes like.
  9. FastA$$89Vert

    Ported Heads and Lower Intake

    For getting the heads ported, polished and resurfaced, and the lower GT-40 intake ported, whats the average price to pay
  10. FastA$$89Vert

    Best way to seal differential cover?

    Im assuming you would use sealant with you put a new cover on....will hylomar do the job?
  11. FastA$$89Vert

    AC Problem.....

    When I turn the AC on in a 95GT, should the front of the compressor spin? When I turn it on, it will spin for 2 seconds and then it will stop, and start spinning again a few seconds later...on and off. The pulley is always spinning but the front parto f the compressor is whats turning on...
  12. FastA$$89Vert

    one last time, will this fit?!

    Im going to pick up the F-303 cam wednesday and I wanna make sure it fits with my Edelbrock 6025 heads with 2.02 intake valves and 1.6 rockers. am i good to go :banana:
  13. FastA$$89Vert

    Best cam bang for the buck?

    Im looking for a more aggresive cam than the E-cam, I dont mind some rough idle, heads and intake are getting ported now and i wanna make some more power, but nothing to extreme, whats the best bang for the buck since everyone is saying alphabet cams are outdated?>
  14. FastA$$89Vert

    What shop would do this?

    oK heres the story, my car is torn down to just the block, pistons, rods, lifters etc in the car. I want to switch cams, but the cam is the part we dont really wanna mess with so id rather have a shop do it. Anyone know a shop that would swap cams if i brought the car to them? somewhere in...
  15. FastA$$89Vert

    Can you install cam.....

    without removing the motor from the car, or taking the front bumper off
  16. FastA$$89Vert

    Help me pick my new cam!

    Ok, Id like to see some opinions on which cam you would choose for my setup. The only thing is, it has to work with 1.7rr without having to make any more modifications to pistons etc. One of the FMS Cams...B/F/X/Z Lunati cam, which would come with the new rollers Crane Comp Cams...
  17. FastA$$89Vert

    OK whats the real answer to this question

    Will 1.7rr work with an E-cam. Simple question But I see so many different answers. Anyone know? :shrug:
  18. FastA$$89Vert

    How much more power?!

    The motor is still apart waiting for the heads and intake to come back from the machine shop and I was wondering, how much more power would i gain from switching to the B-303 cam and the 1.7 rockers? :banana:
  19. FastA$$89Vert

    Porting Question...

    When you port the lower intake, do you have to cut the gaskets to fit the ports or should the gasket already be big enough?
  20. FastA$$89Vert

    Which head gasket(again) Pleas help!

    OK, turns out I have the edelbrock 6025 heads, and I went to order the gaskets today, it says to use a loc wire gasket, then the guy asked me if it has a groove it the heads or on the block for one, but it doesnt? So which one do I use? The loc wire or not.
Top Bottom
Back
Forums
Menu