Search results

  1. D

    Mishimoto Radiator user feedback

    My Mishimoto radiator leaked after about 2000 miles driven in 16 months. Actually, I had suspected a leak a while back but it took being in a Christmas parade to know I had a leak. I put the pressure testes on it, and the coolant flowed out the leak. I put my old stock radiator back on and...
  2. D

    #8 Fuse popping

    Without warning, # 8 fuse popped. Now, it always pops. I've disconnected radio, amp and antitheft. The fuze still blows. Any ideas on what to move next?
  3. D

    Injector timing advice needed

    I inputed my cam specs datalog into EA's Cam Specs tab for computing injector timing. I used Injector firon trailing edge of pulse witdh and TDC timing event. My dist is set to 10deg TDC, so I set Initial Disributor timing to 0. I am using tweecer global timing advance of 6 deg. My cam has a...
  4. D

    EEC Analyzer CAM specs input

    How do I input custom cam specs into the EEC Analyzer software I know thae standard specs, but its to also requires exhaust events open and close. Comp Cams was not any help.
  5. D

    Can pistons be ID'd with heads off?

    I have a mildly built, low mile 351w w/o heads. I'm rying to identify the pistons before buying heads so I can determine the CR and correct CC size to order. The previous owner said that they are TRW forged ffycut pistons, but they don't look flycut to me. They have a large oval dish shape in...
  6. D

    Exhaust leaks do matter

    Had to replace my or-hipe with a catted pipe. I just stuck the air pipe tube in place. I lost a noticable amount of power, but just figured it was the cats. Well, after 5k miles I finally got the air pipe welded up (I was in getting the WB o2 bung welded in). I was shocked, it put me back into...
  7. D

    t4m0.ccf stock tweecer file needed

    Can anyone send me a stock t4m0.ccf tweecer file?
  8. D

    1st clutch install, question?

    I just finished installing a new clutch. Before starting up the car, I re-reviewed all the write ups I had to see if I missed anything. I did. The Ford racing clutch kit included a throw out bearing, which I installed as is. I coated the tyranny input shaft, where the TOB rides, with a light...
  9. D

    Any experience with GT40p CCM-9495 header?

    Any experience with GT40p CCM-9495 header? I was right they do make shorty headers for 94-95's with gt-40p heads. central coast mustang 1-661-823-2400 part number- cc9495 they are 1 5/8 shorty's indurstrail plated cost
  10. D

    How to bottom of intake manifold?

    I gettin a junkyard explorer lower intake manifold ready for install, but the bottom has an 1/8th inch of oil crude. Half of the area is also covered by a metal plate. How do I get rid of this?
  11. D

    TwEECer RT GP $505 ea

    I started a GP on corral and need one more buyer. It's a great price for a great product. http://www.corral.net/forums/showthread.php?p=4872330#post4872330
  12. D

    95 GT vert cat-back opinions

    I'm looking at the following cat-backs for my 95 GT vert; 1. Ford Racing M5230M51 Stainless steel pipe & SS 3" tip, $280, said to be slightly louder than stock. 2. Mac Tru-fit TK7995 Black dura pipe, Stainless steel 3" tip, $320, said to be very loud. 3. Flowmaster force II FL-17214a...
  13. D

    95 seat rear seat cushion removal?

    My rear seat belt latch needs replacing (95 vert), but I can't figure how to remove the rear cushion. Can't find bolts and tried lifting up hard without success. How do I get the cushion out. Anybody have an extra black rear seat belt latch side? Thanks, David
  14. D

    vortech SC and Cervinis ram air hood

    My 93 has the cervinis ram air hood installed, allong with the ram air box. Can the ram air box remain inplace and the vortech intake pumbled through it?
Top Bottom
Back
Forums
Menu