Search results

  1. stangman67

    Does A 6 And V8 Convertible Have A Similar Body?

    Hello everyone, its been a long while since I have been here. My 67 coupe has been serving me well for the past 18 years, but Im getting the itch to redo the body, and am interested in a convertible. Id like to stay with a 67-68 so I can steal the good stuff that i have and restore a convert...
  2. stangman67

    2015 Brakes?

    Maybe its just me, but the standard (non track pack) front brakes look like unbranded brembos? Maybe 4 piston units? They look as adequate as the 11-14 brembos, maybe a smaller rotor?
  3. stangman67

    363 With Smallish Heads? Opinions

    I currently am running a 289 with performer rpm heads (1.90" intake) in a 67. Im running a turbonetics 62-1 with .81 turbine. For this winters upgrade, i have a budget which is roughly limited to either buying a used 331 stock block with studs and girdle with victor jr heads from my buddy, or...
  4. stangman67

    Magnaflow 2.5" system drones!

    About 4 years ago i picked up the magnaflow 2.5" stainless x pipe system for our cars. I added a set of 3.5" tips, about 12-18" long, i dont remember, and it would drone at cruising speeds (around 2100 rpm with the t5). So for the last 3 years i ran it with turndowns, and all the drone was...
  5. stangman67

    How are the exterior lights set up?

    Weird question, but my 67 coupe puts the parking lights on when the switch is in park, but shuts them off with the headlights on. While the front parking lights are on, the turn signals blink the second filment (1157na bulbs), but with the headlights on the turn signal blink the same filiment...
  6. stangman67

    Installed: LMM Power brake booster conversion kit

    Just finished installing a laurel mountain mustang booster conversion in my 67. I had granada discs and 5.0 rear with 9" drums and manual MC. This install was pretty straightforeward, and works very well. It fit with a JMC hydralic clutch kit too. I used the adapter for the pedal, did not...
  7. stangman67

    More low fuel psi issues when hot

    So, last year i was chasing a problem with my nitrous system "surging" when in use. I found it to be my cheapo holley regulator having 6.5 psi at idle cold, and when it warmed up(the motor), it would fall to 2ish. I had a fuel psi safety switch, so it was turning on and off with the fall and...
  8. stangman67

    reenmachine short shifter handle w/ ball

    Looking to sell my short version shifter handle. I comes with a white 5 speed pattern ball, an added $30 value. This shifter is the polished aluminum version, purchased last summer. I changed seats this winter and the handle no longer works for me. $70 plus shipping, or bo. thanks.
  9. stangman67

    17" mach 1 wheels with spacers

    I could really use some money for my house, and I dont know why someone would not want these. Ford motorsport mach 1s with 275/40 rear, 225/45 front in excellent condition with hubcentric spacers. Fit my 67 coupe very well. Please let me know if interseted or you want any more pics. Thanks.
  10. stangman67

    mt et radials: 235/60s or 255/60s

    I am currently running regular et streets, 26x10.5-15 on a 15x7 wheel, and was looking to get one of the sizes above on the same wheels. I used to have a 245/60R15 on an 8" wheel, and those fit, so im wondering which would be a better fit. Both the et radials are measured on a 15x7, so do i...
  11. stangman67

    ford racing mach 1 wheels and tires

    Building a house and looking to free up some cash. I have a set of 17x8 motorsport mach 1s with 225/45s and 275/40s. I have hubcentric spacers with them, 1" in the rear, and .800" up front. Clears everything on my 67 coupe. Going to keep running my steelies this summer. Make a...
  12. stangman67

    68 200ci 3 speed manual swap

    I junked a 68 coupe but pulled everything for a standard conversion. Any interest?
  13. stangman67

    rear kyb shocks

    I installed 5 leafs and the ride was super harsh, so i took out my 3 year old rear shocks and installed some cheapie napa shocks to soften it up. These are good shape, with all washers, bushings, and nuts. You know what they are worth new, make me a resonable offer. Thanks. Mike
  14. stangman67

    Installed 5 leafs and caltracs, need softer shocks

    I put in 5 leaf standard eye, should have used mid eyes) and caltracs set on 1/4 turn preload. The rear sits alittle high, im hoping it will settle, but its is very bumpy now. I have kyb gas-a-just shocks on all corners, and i was wondering what shocks you may have used that offer a softer...
  15. stangman67

    Whats a good fuel pump?

    I am currently running a Holley mecanical pump, the 110 gph version i think, and having some psi issues. I have a typical holley regulator (chrome) with the dual outlets. At startup, i have 6.5 psi, but after it heats up it drops to 4.5-5 psi. As I blip the throttle, watching the gauge on my...
  16. stangman67

    67 coupe $800 on ebay, other mustang parts

    check out all my stuff: http://motors.search.ebay.com/_W0QQsassZmrod67 clutch cable conversion edelbrock carb magnaflow mufflers turbo for I6 fords old school aluminum wheels more... Cleaning shop! Let me know if anything interests you. Mike
  17. stangman67

    modern driveline cable conversion

    selling a 1 year old kit from modern driveline. I used it in a 67 coupe. Worked well but could not keep when i did the unisteer conversion with hooker comps. I was running stock steering and tri ys before. Includes everything that comes in the kit originally except directions and a random...
  18. stangman67

    17" mach 1s with tires and spacers

    Just putting this out there for the spring. I have a mint set of ford racing mach 1s, 17"x8", with brand new Hankook Ventus V4ES tires, 225/45R17 front, and 275/40R17 rear. The rear spacers are 1", and the fronts are .800" which where milled down from 1". This gave me the most fender...
  19. stangman67

    1997 351w swap?

    Good evening, I am asking if anyone has experience with using a late model roller 5.8L into our early cars. Im trying to decide if i can use the short block with a cam swap and my edelbrock heads. What is the engine balance (0, 28, 50 oz), can i use my early timing cover and 1 piece fuel...
  20. stangman67

    Vaccuum lines in boosted applications?

    Currently working on a turbo project, 250ci 6 into a 68 coupe. I am trying to figure out what to do for the transmission modulator and pcv system. Should i just install check valves in these lines, so they dont get boosted? Maybe no pcv system and just run 2 vents to catch cans? Also, the...
Top Bottom
Back
Forums
Menu