Search results

  1. 8

    Heater Hose Removal

    Well, my intake finally decided to let go last night. The nipple for the heater hose broke off and spewed coolant all over my windshield as I was pulling out of a parking lot. I have the parts ordered, and will be driving my fox body for a few days. My question is ...How in the world do you...
  2. 8

    Installing urethane sway bar bushings

    I'm getting ready to install some urethane front sway bar and end link bushings on my '02 GT. Should I support the car on jack stands, or should I use ramps? The Maximum Motorsports installation instructions say to tighten the end link nuts when the car is on the ground to avoid preloading the...
  3. 8

    brake pad question

    On the front brake pads, which is the inner pad, and which is the outer? One has 2 little posts on the back, and the other doesn't.
  4. 8

    oxygen sensor socket

    I'm replacing my oxygen sensors on Friday. Will I need an oxygen sensor socket, or will a 7/8 box end wrench suffice?
  5. 8

    Throttle Cable Mod

    I just did the throttle cable mod, and am thrilled with the improvement in throttle response. I no longer have to bury my foot into the mat to get the car moving. I hate to say it, but this simple mod made a bigger seat of the pants improvement than anything else I've done to it. Of course it...
  6. 8

    Gauge Trim Rings

    I'm shopping for a set of trim rings for my gauges. I have found them at 3 different places, and I'm wondering if they are all the same product. American Muscle has them for $35, but there are a lot of complaints of poor fitment and difficult installation. Mustang Chrome Gauge Bezels, Gauge...
  7. 8

    Summit o/r H pipe

    Is anybody running the Summit o/r H pipe? Is the fitment good? Any problems with leaks? I'm considering ordering their H pipe and the Magnaflow spun metallic cats, and having them welded in.
  8. 8

    Creaking brake calipers

    I recently replaced my front pads (Hawk HPS), rotors, and all brake hardware including slide pins. I flushed the fluid front and back. I bled all the calipers, and the master cylinder. I used brake quiet on the back of the pads, and greased the heck out of the slide pins, and the contact points...
  9. 8

    Tire size question

    I'm looking at buying a set of Nitto 555's for my 02 GT. The wheels are the stock Bullitts, and I'm running 373 gears. I want to step up from the stock 245 width to 255. I'm leaning towards 255/45/17 because I think the 255/40/17 would look too short. My question is, will the difference in tire...
  10. 8

    Anybody running aftermarket pedals other than Bullitt pedals?

    I like the look of the Bullitt pedals, but understand they are pretty slippery when wet. Let's see what else you guys are running.
  11. 8

    Trouble with COP hold down bolt

    I changed my plugs about a month ago, and everything went well. This weekend I pulled the COPS and checked the torque on the plugs. They were all still tight. Everything went well until I got to the passenger side rear COP. I cant get the hold down bolt out. It just spins, and the insert in the...
  12. 8

    Hawk HPS pads too thick?

    I installed new front rotors and Hawk HPS pads. The pads are so thick I had to grind down the little posts on the back about halfway just to get the calipers to go over them. They are so tight now the pads are gripping the rotors. I did a Google search, and it seems like quite a few people are...
  13. 8

    vibrating side mirror

    My driver side mirror is loose in the housing and vibrates so bad I can't hardly see out of it sometimes. It's the actual mirror part that shakes. Has anyone else had this problem? What is the fix for it?
  14. 8

    Anyone own a California Car Cover?

    A storm on Christmas Eve shredded my already ailing Wolf car cover. I need to replace it soon. I've been looking at the California Car Covers in the Superweave fabric, and wondering if anyone has any experience with them.
  15. 8

    Wheel well coating?

    I'm wanting to freshen up the rear wheel wells of my '89. Can anyone suggest a spray on product. I'm looking for a permanent coating not a dressing. I also want to keep it factory looking.
  16. 8

    PA Performance alternators, are they good?

    I'm thinking about ordering an alternator from PA Performance. Any opinions?
  17. 8

    gauge cluster lens

    Has anyone successfully seperated the lens from the black plastic piece that frames the gauges?
  18. 8

    Has anyone painted the running horse on the steering wheel?

    I saw in a thread where a guy used a metalic sharpie to color his horse and Mustang script on the dash. I was wondering if anyone has used a different method, and how it turned out. Pics would be great.
  19. 8

    replacement mirror glass

    Does anyone know where I can find replacement mirrors (just the glass) for my 89?
  20. 8

    Placement of engine bay decals for an '89

    Does anyone have a picture that shows the factory placement of the decals in the engine bay of an 89 5.0? I know about the one on the coil cover, and the airbox. I'm mainly concerned with the ones in front of the radiator.
Top Bottom
Back
Forums
Menu