Search results

  1. 1

    Are Cometic MLS head gaskets really worth the extra money??

    I think I just blew my new felpro 1011-2 head gaskets and I was wondering if the Cometic MLS head gaskets are really worth the $160 price tag? I was running too much timing and I'm pretty sure I toasted my felpro's this weekend. I'm new to the whole supercharger scene, so I guess one set of...
  2. 1

    HELP!!! No vacuum after head and intake swap.....

    I just finished a head and intake swap and now the car has no vacuum and will hardly run. I have to keep giving it gas to keep it running. If you hold the gas pedal at a constant spot then the rpms go up and then down repeatedly. I'm running a holley systemax intake with performer rpm heads...
  3. 1

    What are the colored vacuum lines for at the back of the engine compartment?

    I have got a few broken colored plastic lines at the vacuum bundle and was wondering if any of these lines can be done away with. What are they for?
  4. 1

    Which wire is the oxygen sensor signal wire?

    I'm hooking up an autometer air/fuel gauge in my 93 and I can't remember which wire is the signal wire on the oxygen sensor harness. Anyone remember which wire they used? thanks, Matt
  5. 1

    Is there enough clearance to run "Tall" valve covers on a EFI stang?

    I have performer rpms with a holley upper and lower with a 1" spacer and I wanted to install some polished valve covers and was wondering if I can clear the polished Ford Racing ones? Anyone run tall valve covers on a efi car?
  6. 1

    Who runs 24lb injectors with a supercharger?

    My current combo is a h/c/i with a novi 1000(5-6lbs boost) with 24lbers and a walbro 255lph pump. I'm just wondering who is making 24's work for them with a supercharger. What is the hp limit with 24's and a fmu? thanks, Matt
  7. 1

    What length pushrods with Edelbrock Performer RPM's?

    I was needing to know what length pushrods to use with a small cam and performer rpms. They are the small valve rpms. Part #60229 thanks, Matt
  8. 1

    Is 400RWHP asking too much from this combo?

    I'm going to dyno the car next month once I do some more tuning on the street. Car is as follows: Forged 306 with 8.7:1 cr AFM B-31 cam Edelbrock performer RPM heads #60229(1.9/1.6 valves) Holley Systemax upper and lower with 1" phenolic spacer BBK 70mm throttle body Harland sharp 1.6...
  9. 1

    Does anyone use these Performer RPM heads? Part #60229

    They are the Performer RPM heads with the 1.90/1.60 valve package for stock pistons. I was looking at getting a set for my 306/novi 1000 combo and was wondering if anyone is using these and how they like them. I'm also wondering if they will come with all the accessory holes drilled so they...
  10. 1

    Which injectors and fmu disc would best suit my combo?

    First off I have no local tuners that can burn a custom chip so I will have to do all the tuning myself. With that said I need to be as close on with the tune as possible so I can be safe when I first run it to start tuning. The combo is as follows: Paxton Novi 1000(6lbs boost for now)...
  11. 1

    What's the difference between a 1992 and 1993 AOD tranny?

    I'm looking at getting a converter for my 93 AOD car that I just bought and I see converters listed from 87-92. What's the difference?
  12. 1

    Is the B&M hammer a good shifter for a AOD?

    I'm looking to get an aftermarket shifter for my aod car and I'm wondering if the hammer is a good choice. Does it have the provisions for 1-2-D-OD or just 1-D-OD like the stock one. I don't like doing the 1-D-1 shuffle. I want a shifter where I can shift through the gears like normal without...
  13. 1

    Can I use a smog pump eliminator kit with a supercharger?

    My car has a Novi 1000 on it and I bought the smog eliminator kit today hoping that it will work. It's just like the motorsport one. It is supposed to bolt up just like the smog pump, but it has a free wheeling pulley on it. Does anyone use this with a supercharger and does it bolt up fine...
  14. 1

    Do you need rocker stud and spring upgrades on afr 165s?

    I was fixing to buy a set of afr 165's and people have said that you need to upgrade to arp studs with the afr upgraded springs. Is this true for a mild 306 with a cam of about 500 lift and won't be shifted over 6,000 rpms? thanks, Matt
  15. 1

    Will I be able to use an A/C eliminator kit with my novi 1000?

    I bought a car that has a novi 1000 on it and was wondering if I would be able to use an a/c eliminator kit such as the March, Ford, or Trick flow kits.
  16. 1

    Will I have any clearance issues with long tubes and an AOD?

    I have always had 5 speed cars with no clearance problems. Now people are telling me that I won't be able to clear long tubes with an AOD. Anyone run long tubes on an AOD car? How was the fitment?
  17. 1

    What size injectors should I be using?

    Mods are as follows: 8.5cr 306 Ported E7's E or B cam GT40 upper and lower 70mm throttle body Paxton Novi 1000 6lbs boost Built AOD with 4.10's The car currently has stock injectors in it and I'm thinking that might be a little lean. I'm debating on putting a set of aluminum heads...
  18. 1

    Are you supposed to run synthetic when using a blower?

    I just bought a car that has a Novi 1000 on it with a fresh 306. The previous owner said that he had been using Castrol 10W30 conventional oil in it. I had a local tell me that I'm supposed to be using synthetic beings that the paxton is fed by the engine oil. Is there any truth to this?
  19. 1

    AOD guys, help me find out what gears I have......

    I just bought an AOD car and I'm trying to figure out what gears it has. The owner told me that it had stock gears. Like a 3.27 or a 2.73 gear. When I'm running about 60 mph, the stock tach in Overdrive is reading around 1,600-1,700rpms. Does this sound about right for a stock geared car...
  20. 1

    Crank just broke in my DSS 331 Pro Bullet!!!!

    Well I drove the car out to Advance Auto in town to pick up some spark plugs for the tahoe and when I left I got down on it in first gear... What did I do that for...the instant the revs started to climb while it was spinning I hear this loud noise that sounds like a grenade went off under my...
Top Bottom
Back
Forums
Menu