Search results

  1. 90_Red_LX

    Water Leak On Passenger Side, Coming From Up Top.

    Hey guys, I was curious to know if anyone had any culprits to where a water leak could be coming from on the passenger side of my fox. It's coming from the front right corner it kind of looks but it drips right in the center of the passenger seat. Anyone ever had any issues with a water leak...
  2. 90_Red_LX

    Finally Near Done

    Finally got her where shes looking near 100% and driving a lot more. Even bought a tremec for her. What you guys think? Driveways sloped back end sits lower than that.
  3. 90_Red_LX

    Does This Car Look If It's Sitting Too Low?

    Just curious if anyone had a fox sit this low in the front. Tires tuck, but the fenders starting to tuck over them. Haven't had time to mount the fenderwells in yet. Front setup is Eibach sportlines, tokico blues, x2 balljoints, stock control arms, poly bushings, and MM C/C plates. The first...
  4. 90_Red_LX

    Driver Front Hard Brake Line Routing?

    I'm trying to get the car finally running after two years this weekend. I converted 5 lug and discs. I got all the lines ran but the drivers front, and for the life of me I can't remember how it went. Anyone have any pics or decent description? I think I'm over complicating it. Thanks.
  5. 90_Red_LX

    Throttle Cable Woes...now Holding Tb 1/3 Open

    I've been building the stang for two years, and I have forgotten how the throttle body cable goes on the bracket. However, either way I go whether the little bracket for the screw is on the front or back side of the bracket, the cable is still too short and holding the throttle about 1/3 open...
  6. 90_Red_LX

    What Is This Connector?

    Sorry if I'm flooding the forum with questions here lately, but trying to finish this build up. I've got this connector under the dash flopping around, and I don't remember where it goes. I'm just praying the dash isn't coming back out. Anyone recognize this piece? I pulled the inside out...
  7. 90_Red_LX

    Rear Springs Not Staying In.

    I bought a set of MM adjustable rear control arms and the rear end keeps dropping too low to keep the springs in. The springs when I jack the adjusters up doesnt let the spring sit nice and flush on the bottom. The pigtail on the bottom of the spring is jacked up a little. All control arms...
  8. 90_Red_LX

    Need Tire Size Recommendations

    What tire sizes would you guys recommend for a 17x10 rear and 17x9 front wheel size? They're 10th anniversary wheels. Thanks.
  9. 90_Red_LX

    Ball joints for 5 lug swap and 03 cobra steering rack

    Alright, I understand 93 taurus tie rod ends are the way to go for an 03 cobra steering rack swap. The 03 rack is mounted in the car now. Stock a arms, 94/95 spindles, tokico blue struts, mm caster/camber plates, and eibach sportlines are my front end setup. What ball joints should I use...
  10. 90_Red_LX

    fox length axles or sn95? And what else for 10in rim?

    I have a set of 17x10 10th anniversary wheels that I need to get mounted on the car. The time has come to round up the necessary parts. The front end I have under control, the rear wheel wells have been rolled, and if necessary take the inner wells on a date with the ol bfh. However, which...
  11. 90_Red_LX

    My Fox build

    So a couple years ago I had a introduction of the front nose and driver fender to a guardrail in the rain, and what should have been a simple fix and go turned into an all out stripdown and rebuild. This is how she sits now. What do you guys think? Doing a 5 lug conversion, bullitt/cobra...
  12. 90_Red_LX

    Clip for temp control cable?

    Anyone know where I can find the clip for the temp control cable to attach it to the heat box? I ripped my dash out over a year ago, and now can't. Search NPD and LRS to no avail. Thanks.
  13. 90_Red_LX

    17x10 Saleen Ssc On Fox?

    Searched the web, hit or miss on the answers I am looking for. I have a 90 lx hatch in the shop now getting the fenders rolled and resprayed. I want to run the 17x10 saleen ssc wheels deep dish in the back. Can I run those without bashing the inner fender in, or do I have nol choice? Quad...
  14. 90_Red_LX

    Hard lesson on drag radials in the rain

    I've always been lucky driving my car in the rain on drag radials, especially with my attitude, but after of a couple years of luck, last night bit me in the rear. Coming down the on ramp with was a swooping steep downhill ramp to the highway, I gave her a lil too much throttle before I...
  15. 90_Red_LX

    Black magic fan popping fuses suddenly

    I've had a black magic fan for a bit now, used to not give me any trouble, but now it's just popping the fuse on the power cable instantly. I'm not a wiring guru by any means so I'm stumped. I have a 12v source for the thermostat for the fan in the fuse box in the car, running the big power...
  16. 90_Red_LX

    t5 gurus, yet another tailhousing and shift fork issue

    Hey guys, sorry to make another post about this, but the shift forks and the tailhousing are giving me fits. I read on another post last night to pull on the 5th gear rod a bit, and the tailhousing will drop. Well the tailhousing will find home, but it then jams the shift forks and I cant...
  17. 90_Red_LX

    Anyone ever took a sunroof latch apart?

    Anyone ever took their sunroof latch apart? I did while I was replacing my headliner, and now I'm screwed and can't remember where the little spring, washer, and little plastic nipple lookin thing goes.
  18. 90_Red_LX

    Dash gurus, black vac line question

    Hey all, where does the black vacuum line that comes through the firewall connect to on the dash side? A lot came up and I forgot a few things, and I can't figure this one out. Runs on top of the box. Thanks.
  19. 90_Red_LX

    Good harmonic balancer?

    I'm looking for a good harmonic balancer for my combo, got rubber pushing out of my current setup. Just curious what you guys recommend.
  20. 90_Red_LX

    t5 gurus, please stop in

    Having problems with my latest trans rebuild. Been gone through 3 or 4 times now, so I'm not a newbie at it, but it's been a while since I've last done it. My problem is when I torque the input shaft retainer down, and put the tailhousing on, the mainshaft gets in a bind, even without a shim...
Top Bottom
Back
Forums
Menu