Search results

  1. tnardo

    01 3.8 to 5.4 swap

    about to start a 3.8 to 5.4 swap in an 01 mustang, does anyone have any info and or links on this swap.
  2. tnardo

    breakout box, grounds 40 & 60, ohms reading koeo, koer ... help!!!

    im having a problem with a car randomly shutting off while running i hooked up the breakout box, i have 1.4 ohms on both pin 40 and 60 with the bat dissconnected( shut off switch) while running it goes up to .400 ohms. it does fluctuate.... when it shuts down its spikes upto 7.95 k.. what...
  3. tnardo

    Msd pro power coil

    i have an msd pro power coil it says it is for the 7 and 8 sytems can i use this with my 6al
  4. tnardo

    blow by. after headgasket replacement. oil everywhere

    ok i have an 81 f100 with a 300 straight 6 last weekend i put a head gasket out. i believe it may have been partially leaking for a long time. because there was tons of build up on the spark plugs last year also. the truck never overheated heck im lucky if it is even in the n of normal. also the...
  5. tnardo

    do i need a vacuum switch and other vacuum questions

    i'm running carbed..all i need vacuum for is the vac advance and brake booster...but later i may hook up some ventalation..... i have an oil filler cap that has a pvc on it where should i run that line into the intake.. or somewhere on the carb....the tbig fitting that come out of the fuel...
  6. tnardo

    how to relocate starter solenoid to the trunk..anyone done this

    i was reading a post on here earlier and someone was talking about being able to relocated the starter solenoid to the trunk.. how do i do this... what about all the wire that go on with the positive cable
  7. tnardo

    green wire that says fusible link 14ga

    i have a green wire comming from the headlight harness it has a connector on it that looks like it should goto the solenoid and its right by the solenoid but i havent seen it in any pics i've found can someone tell me where thise wire goes
  8. tnardo

    replacing brake lines

    i want to replace the brake lines that are in the engine bay master cyl to combination vlave and comb valve to brakes im going to replace all lines except what runs to the back(already done) i want to clean up the engine bay a little do i have to keep all the bends the same or can i just...
  9. tnardo

    performer rpm install...what goes here??? and which throttle cable

    i cant seem to figure out what goes in these holes look at pic to see where im talking about #1 its a threaded hole. it does not open up into the intake #2 threaded hole. it opens up into the intake...maybe for a vacum fitting??? #3 does the sender for my mechanical temp gauge go here #4...
  10. tnardo

    black and grey connectors on driver side harness

    Im in the process of doing a 4cyl - 5.0 carb swap. I know it's not really necessary to know what all the wires mean but i would really like to know. i broke some wires when i was relocating the harness. what i need is a pinout for the black and grey connectors....what is each wire for...
  11. tnardo

    one'mo'gain....chassis grounds, engine grounds, battery grounds

    im just finishing up my 4cyl to carbed 5.0 swap. and i need to know what grounds i need to hookup. where does the neg battery cable hookup... there is a round connector on the neg. cable.. i believe it went to the eec harness do i need to do anything with that.... i need a ground strap...
  12. tnardo

    Duraspark help!..everywhere is different .. i need an expert

    im wiring up my duraspark...it's out of an 85 gt along with the distributor. everywhere i look to figure out where wires go i seem to get a different answer.. so let me tell you what i see and what ive done so far I know what to do with the 4 wires that come out 3 goto the dist and the green...
  13. tnardo

    no ps no ac no smog what belt

    all im gunna run on my car is the alt and water pump what size belt do i need and how do i route it
  14. tnardo

    4cyl to carbed 5.0...vapor line on gas tank????

    i ran new fuel lines all the way with a custom pick up tube i still have a line that runs down the pass side.. i'm guessing it went to the evap canister what do i do with this line can i just leave it hangiong open __________________
  15. tnardo

    tightening rear control arms bolts after 8.8 install???

    i installed an 8.8 in my 89 notch. how do i have the car sitting when i tighten the rear control arm bolts.....axle on jackstands?....car on jackstands, axle hanging....or car on jackstand axle partially elevated with jack..???
  16. tnardo

    2.3 to carbed 5.0 swap duraspark wiring

    im installing duraspark on my 89 it was a 2.3. i have everything from an 85 gt. but i keep reading about this resistance wire for the durspark. the wiring harness is junk from the 85. so im hard wiring in the duraspark. ive researched all the links and im still not exactly sure how to...
  17. tnardo

    post your e.t's and hp with gt40 irons

    what times and hp numbers are you getting with gt40 iron heads. post cam, compression and other mods. if yall could
  18. tnardo

    4cyl gauges with a carbed 5.0

    I put a %.0 in my 89 4cyl car. I'd like to use the stock oil, coolant, and battery gauges. I have the edlebrock performer rpm intake. what sensors do i need to buy. i would think i should get 89 5.0 sensors... am i correct?
  19. tnardo

    installing 8.8 in a ex 4cyl car need help with brake lines

    ok the rear end is in and i put in brake lines from an 8cyl car. i also bought the new rear brake line, it has a hose with a banjo bolt and a box where the hose goes into and two fittings are on the side. the rear end has both lines from each side going to a box that also has a hose comming...
Top Bottom
Back
Forums
Menu