Search results

  1. R

    Help with Shelby ID?

    Here is a pic of a car that was found with VIN 7R01C160605. A couple of strange things about the car. The VIN says 289/2bbl. It is a 'california special' fitted car but a 67. It has the taillights, and trunk area... no quarter panel vents. It has a stuffed 429 at this point. Just...
  2. R

    Windsor fox EFI conversion - hard time starting

    I have a hard time starting my car. It has the Windsor fox EFI conversion harness and the problem is the following: When you are turning the key to the 'start' position, it it turning over, but it really isnt firing. When you release from the start position, it will try (and most time...
  3. R

    Export brace/monte-carlo bar fix/suggestions

    I have a 67 EFI I am finishing up all the final details on and I have a question on the export brace I am using. Currently, it is one with rod end links on both sides of the brace and there is NO monte carlo portion at all. I saw on the other gentlemans car, he had to modify is severly to...
  4. R

    67 Restomod Progress w/Question

    Two things... this is an update on the car... been a WHILE. Got it inspected, insured and started driving it see if anything showed up. So far, nothing except what I need help on... This is a EFI converted and it is falling on its face right off idle. It backfires and fires in the exhaust...
  5. R

    Rear Seat Upholstey Help

    I have searched the web and most help is with the front seats. I need help with the rear. It is in OK condition, but the canvas and metal strips inside the canvas are showing some wear (its a 67) Is it best to replace all that and the foam, or reuse it? Where do you get the canvas with...
  6. R

    Need help, 67 pillar pad install

    I need help installing the new pillar pads. The car orginally came with them, but they were in terrible shape and quickly removed and discarded. Now that it is time to install the new ones, I cannot figure out how to do this.... the headliner was easier than these. There are two sets of...
  7. R

    After forever... finally some progress

    I finally got some progress done on my car and the cardomain site, so I would appreciate any/all comments on the car. Lets hope for good progress this year. Mark http://www.cardomain.com/ride/2224648
  8. R

    Wanted: Two top pieces of windshield trip on 67 coupe

    I need just the top two pieces over the windshield... I dented mine putting them on and I dont want to buy the aluminum ones they sell as a replacement. They dont have to be 100 point restoration perfect as this is a daily driver (restomod restored) car that is quite nice... just no dents...
  9. R

    Windshield chrome on 67, need help, I dented one

    I had my new windshield installed yesterday and he wanted to put the chrome in, but I wasnt ready, I needed to polish it... so he said no big deal. Anyway, I polished it all up and started installing it... the bottom and side pieces went in fine, but the tops will not go at all. I dented...
  10. R

    Another quick windshield install question

    Do you need to install the dash (in a 67 first) or can it be done after the new windshield is in place? There are two small pieces of metal that need to be screwed in place near the bottom of the windshield and that is my biggest concern. Thanks!
  11. R

    Windshield install - specific question

    I looked all through the web and archives... and I have a very specific question. I am installing my rear glass first in a 67, and I have put the non-hardening sealant in the weatherstrip and placed it on the glass first. Now I am supposed to install the glass in the car. Some folks have...
  12. R

    Headliner sound/heat barrier

    I asked this on the bottom of another headliner question, so I apologize for the double post... but... I have dynamat extreme installed on the roof metal on a 67 coupe. I was messing around and starting fitting the headliner and it went in pretty quick, BUT, I have not installed anyything...
  13. R

    Front bumper fit on 67

    I am trying to put the new bumpers on my car and I have a different opinion vs. what the parts are trying to tell me. When I bought the car, the front bumper and grill area were not straight at all. I have replaced all those parts and I thought the front bumper would be as easy as the rear...
  14. R

    White lithium vs synthetic grease on window parts?

    I am about to put all the window regulators, frames, channels etc back together on my project and want to know what grease to put on all the parts. Mustang monthly did an article saying to use the white lithium grease, but was that because what is original, or what is better? I am a big...
  15. R

    67-8 8" rear, v-8, 5 lug $50

    I am in the Dallas/Fort Worth area and have an 8" , non POSI, 2.7x gear rear for sale... $50. Needs a new home, and is complete. Great for a 6cyl conversion car. I will not ship.
  16. R

    Paint help needed, DFW area Texas

    I need the top of a hood, top of trunk lid and side vents for a 67 painted. I have the paint and clear, just need someone with a place... does anyone know of anyone who can help?
  17. R

    Just finished final priming!!!!

    :D I just finished the final priming on the car... I dont have pics yet but 3 2 1 days till paint!!! I cant wait till this weekend :D
  18. R

    Just built my first roller spring perch

    I just threw one together today to see how hard it was, and it was easy.... the only thing there is one 'tight' spot in the bearing during full rotation. I can only imagine while in use on the car, you would see a maximum of 30 degrees full motion, so I dont think it would be a problem...
  19. R

    Final priming pics... 67 EFI restomod

    I have finally completed by last piece priming on my car. The final is to shoot the whole car again and block it. Almost there!
  20. R

    Need pics of 67 horn mounting...

    I neglected to take pictures of that part when I took them off, and I replaced the core support with a new one. Nothing seems to look right in the mounting of the horns... maybe the holes arent there. Can someone post up some pics of the way the horns are supposed to be? Thanks, Mark
Top Bottom
Back
Forums
Menu