Search results

  1. D

    Electrical 99 GT No crank condition

    Turned out to be the ignition switch. $25 bucks and it's back on the road.
  2. D

    Electrical 99 GT No crank condition

    Okay so I have a 99 Mustang GT 4.6L 5 Speed. The other day I got in it like I usually do and went to start it and it cranked for 1/2 a second then stopped. Now it won't crank at all. I turned the key and there is nothing, but everything else seems to light up and work. I've tried leaving...
  3. D

    Sandblasting Rims

    Yes they are sandblasted then a powder is applied and baked on at 400 degrees. Look up powder coating in your area I'm sure there is someone around. Sent from my SAMSUNG-SGH-I777 using Tapatalk 2
  4. D

    Sandblasting Rims

    If you want them to last get them powder coated. We do them at my work for 50 or 60 a wheel. Paint will chip easily, a good powder coat finish won't. Sent from my SAMSUNG-SGH-I777 using Tapatalk 2
  5. D

    I Need A Decent Head Unit

    Kenwood. 'nuff said. Sent from my SAMSUNG-SGH-I777 using Tapatalk 2
  6. D

    Bent control arm? k member?

    I'll take a better look at it this week sometime. but the front end is all stock so stamped mild steel. hopefully its just the control arm that a lot easier to replace. Sent from my SAMSUNG-SGH-I777 using Tapatalk
  7. D

    Bent control arm? k member?

    so the other week I slid into a curb pretty hard going too fast around a wet corner. yeah I know stupid. broke two right side rims. so I got new rims, it drives fine but I noticed the front tire is pushed back about an inch and not centered in the wheel well. from my research so far its...
  8. D

    car cutting out

    just wanted to update everyone. It was the TFI (ignition control module) I replaced it and my car works as good as ever. thanks for the advice.
  9. D

    car cutting out

    I've replaced the ignition coil, cap & rotor, fuel pressure regulator, fuel pump, and also checked the TPS, MAF, Timing. The car acts like it is hitting a rev limiter. If while accellerating I hit 4300 rpms it basically falls on it's face if I shift and drop the rpms it will continue as it...
  10. D

    car cutting out

    My car stops accellerating at 4300 rpms. I can't figure it out for the life of me. I've even taken it into ford and it's throwing no codes and they say it's running fine. The guy told me it's the injector cut out to protect the engine. Funny thing is it used to rev all the way to 6000 rpms...
  11. D

    Exhaust Fitment Question?

    I'm looking at a used Roush Side exit exhaust system. The car it came off of is a '02 GT Roush Stage 2. The guy says it'll fit 94-04 cars. Is this true? will it bolt up to my 94 5.0?
  12. D

    Sub install pics.......

    I have 2 10W1V2 Downfiring in a ported box in my Vert. It sounds phenomenal. Thats the upside. The downside you ask. Well I basically have no trunk anymore. :(
  13. D

    Lowered too much?

    I've attached the only pics I have here. I'll get different pics tonight or tomorrow. It doesn't really look that low but I'll get an underneath pic to show the clearance. It's not like it hits all the time. Just on really big speed bumps.
  14. D

    Lowered too much?

    I just bought a '94 gt. pics already in another thread. My questions is this: It's obviously lowered, I don't know which springs are in there. When I drive over a large speed bump, even really slow, the tranny cross member sometimes hits. Is this normal for a lowered mustang. Or have maybe...
  15. D

    my new ride

    Well heres my new ride. I just bought it and so far so fun. 1994 Mustang GT Convertible Black/Black/Black 17" Gunmetal Bullit rims Lowering Springs Subframe connectors I really like it. I've only owned it for 2 weeks and it's already down at my local stereo shop getting the works...
  16. D

    Put my 94 to the first test

    well it's the last light before going out into the country. no sidewalks and just orchards all around. I'll post some pics tonight. I also don't condone going all crazy through town. I usually save it for the empty country roads, that way if something happens I only hurt myself.
  17. D

    Put my 94 to the first test

    Well I'm a newbie here and this is my first post/topic. Just 2 weeks ago I bought a '94 Mustang GT Vert. Triple black, lowered on 17" bullets with flowmaster exhaust, and subframe connectors. I don't know if anything else has been done I haven't gotten to look to deep yet. I hadn't put the...