Search results

  1. B

    Is it safe to use a 170 or 200 amp alternator?

    Thanks for the tips-I do have the moroso 74102. I wish I had found that diagram a few months ago. Has that wiring scheme been proven? My wire scheme did work until the smaller stud were loosened and now the small studs are no longer continuous. any idea why the jumper wire on 3/16"...
  2. B

    Is it safe to use a 170 or 200 amp alternator?

    I am not doubting your numbers as they seem reasonable, I am questioning the actual amperage that is going through the wire. Like I said I am still trying to understand the alternator. If it takes 80 amps of current to push my accessories are you saying there is actually 80 amps of current...
  3. B

    Is it safe to use a 170 or 200 amp alternator?

    One thing I would like to clarify , as I am trying to figure out my own alternator issues at the moment If I have a 130 amp alternator (sn95) are you saying I need a 3-4 gauge wire from the alt to the battery? I have to disagree because the sn95 didn't even come with a 3-4 gauge wire from...
  4. B

    Parting out 98 Cobra 28k original miles!

    hasn't replied since 9/23/2009 safe to say this thread is dead....
  5. B

    Excessive Motorsports vs Springfield Motorsports

    I'll give this thread a bump- I am thinking about going to Springfield Motorsports since it is literally a mile from my house. I would like to get some dyno pulls to see what my car is doing-I've got a tweecer so I don't know if they will actually be able to do any tuning-I basically want to...
  6. B

    Fuel Pressure Safety Switch with Zex Wet Kit

    Ill give this a bump, I just installed a NOS15685 adjustable cut off switch. I spliced it in to the chassis ground wire for the NMU. Very simple and seems effective- anyone know what it should be set it? I have mine set to turn off the nitrous for everything except wide open throttle (fuel...
  7. B

    power adder forum?

    cool thanks for the info, I know there use to be it has been so long I thought I might be over looking it...
  8. B

    power adder forum?

    is there a forum to discuss nitrous/turbos etc?
  9. B

    Tweec #1: Search For a good idle!

    ya I am considering getting EA. I am corresponding with Mike from the eec tuning forums who is running my data logs through EA. With the first run through EA is actually liking my setup right now. It has only minimally changed my injector slopes. I need to find time to do some more data...
  10. B

    Tweec #1: Search For a good idle!

    Update I have cleaned up all the wiring to the o2 sensors. The wiring had been spliced and bare wiring was showing. I went a head and re did the splices nice and clean with heat shrink. I replaced the o2 sensors. Finally I fixed a some exhaust leaks. All of these changes got my o2...
  11. B

    Electrical Gurus inside please! Bad ground? (o2s)

    IT should be grounded, it is also the ground on the EEC Tester plug.
  12. B

    More Fuel Pump Problems!

    Yes I have started it and it runs just like it had been over the last couple of weeks.
  13. B

    More Fuel Pump Problems!

    Fuse is good. Interesting Update: I pulled the PCM out sort, of made sure tweecer was secure. The tweecer seemed pretty secure. The fuel pump did not prime. I took a break did nothing to it, and a few minutes later the fuel pump seems to be working like normal. Problem is the pcm is on...
  14. B

    More Fuel Pump Problems!

    By the way, I have just completed a circuit test at the CCRM. I found that when the ignition is turned over to on or cranking I get no voltage at pin 5 (DrkG/yello) which I believe to be the voltage source for the fuel pump.
  15. B

    More Fuel Pump Problems!

    I have checked the inertia switch and fuses and both seemed to be ok. My next step is to jump the fuel pump to double check that it works. I have a feeling something in the relay circuit is not quite right. I recently jumped the fuel pump through the data link and know what the relay...
  16. B

    More Fuel Pump Problems!

    I have recently installed a new fuel pump that has less than 100 miles on it. My problem is that it suddenly stopped working. I have tried to jump the pump at the data link connector with no success. When I jump the data connector I barely hear the relay click at the CCRM. I have done...
  17. B

    Smog pump, A/C removal question

    I didnt really notice any performance difference. I did notice how much cleaner the engine bay is.
  18. B

    Bryan/College Station/Houston Anyone?

    Cool! is he a stanger? I have not met to many people in College station that race, I hope that changes though. ca
  19. B

    Electrical Gurus inside please! Bad ground? (o2s)

    Hey guys most of you remember I am in the process of tweecing and I wanted to verify all of my wiring/grounds are good because of the way my 02s were responding. I was analyzing my wiring system and found something I thought to be pecuiliar. I am not sure if any one will be able to help but...
  20. B

    Basic info: Welding?

    For some reason the places I have gone here have told me the same story. They must be strict in this town. I am sure part of it is they don't wanna screw with some custom stuff too. There is one place down the street that might have a welder so I will check them out. Maybe I can get lucky...
Top Bottom
Back
Forums
Menu