Search results

  1. I

    Makin' room for a new H.O

    The CSI investigation of the short block is complete. It is so messed up! The piston skirts and bores are really scuffed-up. The main and rod bearing are wasted. The crank has no deep gouges but has many hot spots in it. The rods made it out o.k. Thankfully the Edelbrock heads are fine. The...
  2. I

    looking for some CarDomain pages

    I have been on holiday for a week and a bit, the money ran low early so I updated the crap out of my car domain page:rlaugh: http://www.cardomain.com/ride/2669362
  3. I

    Makin' room for a new H.O

    I removed the engine from the Mach the other day. I have a few days off of work, so on Monday I will do a mini CSI investigation on the engine. The drivers side head was seeping a little coolant out. I think I will have the heads plained and have the intake machined so it actually fits...
  4. I

    Wheels-Tires Wheel/tire Combos Known To Fit

    I called centerline for a customer and they said that they no longer build wheels with our bolt pattern
  5. I

    Wheels-Tires Wheel/tire Combos Known To Fit

    This is a good link! http://www.rsracing.com/tech-wheel.html#backspace
  6. I

    Wheels-Tires Wheel/tire Combos Known To Fit

    I am looking into buying these wheels. Revolution Classic 4 spokes. 14x6 with 4" backspace. Do you think I will be able to get away with it or will I need some thin spacers??? They are $250.00 U.S a pop plus $79.20 for a set of special sleeve wheel nuts...
  7. I

    Power cutting out

    I had a similar problem with my II. I had a Holley mechanical pump that was faulty. I replaced it with a carter HP electric and a Holley Regulator and now I run out of guts before the mach runs out of fuel :D I upgraded all the lines to 3/8" as well.
  8. I

    Interior Fire Wall.

    A bulkhead would likely be safer, but you would have to be a sheetmetal engineer! Try to build a balk-head around two angled roll cage struts, strange shaped wheel housings, a 10lb nitrous bottle and a big-ass rear window. :D Then try to make it look presentable!
  9. I

    Rear bumper fabrication

    http://forums.stangnet.com/attachment.php?attachmentid=32144&d=1104715261 My Mach:D
  10. I

    Rear bumper fabrication

    I bought the Mas fiberglass bumpers. They were very inexpensive. Like $79.00 each! I peeled the original bumpers off and sand blasted the metal behind. The body shop then bonded the new bumpers on with "Vette-Bond". The bumpers and the Mustangs Unlimited dront spoiler are all made of thin...
  11. I

    Interior Fire Wall.

    That sounds easy, compared to what I was thinking of, thanks:D
  12. I

    Interior Fire Wall.

    I have a 78 Mach 1 (hatchback of-course). My car has a Competition engineering 6 point roll cage in it. My fuel cell is in the hatch also. I need to construct an NHRA legal "fire wall" between the fuel cell and the passenger compartment. Does anyone have pictures of their set-up?? I need...
  13. I

    Mustang II TV commercial

    You dudes seen this?? http://mustangii.net/1974_commercial.asp Good Stuff:D
  14. I

    power steering ?

    I ditched the power rack for the manual rack. The problem is the stock II manual rack is way too slow!! The lock to lock is like 4 1/2 turns! (guess-ta-ment). I am going to put in either a flamming river rack or a stock power steering rack without a pump back in. I think sleeper put a II power...
  15. I

    New Chin Spoiler

    I have the Mustangs Unlimited spoiler on my II. I made a couple of steel reinforcements for it. To be honest it looks really fragile, and when I put it on I figured for-sure I would break it. It has been on there for years, and it has held up really well. I suppose the fact that it is really...
  16. I

    Need a new Toilet Seat!!

    Does anybody have a toilet seat for a Mustang II?? The bolt out part that the strut rods bolt into, and the transmission crossmember bolts to???:lol: My toilet seat was rusty around where the bushings went in. When I restored the car, I welded washers to it and bolted it up solid.
  17. I

    C-clip elimitators???

    Who makes c-clip eliminators for a 2005 Mustang GT??:shrug:
  18. I

    Ford Racing Mustang II Wheels???

    Have you dudes seen this??? They will probably come out when hell freezes over:shrug: http://www.fordracingparts.com/mustang/main-s4.asp?vehicleid=3&year=1978#fromFlash
  19. I

    5.4l swap headers???

    The customers always right, that's why:D Thanks for your imput, ya it looks like a kustom deal.
  20. I

    5.4l swap headers???

    Does anyone know who makes headers to put a 5.4l Navigator engine into a 2003 Cobra Mustang??:shrug:
Top Bottom
Back
Forums
Menu