Search results

I know that if you have a sct flash on your computer that it will void the warranty, but if you return it to stock, can ford tell that you had it previously on? I thought I read somewhere that the computer makes a note of it and ford would be able to tell. Its an extended warranty, and I'll more...

I just got my 2004 cobra, and have never owned a modular car before. Before I bought it, I did the usual checking to hear for the head tick and heard nothing. I don't think its the "tick" issue (louder at the passenger side than driver) but just wanted opinions on the way the car sounds. (Just...

So I never picked up that 10th annv. I asked you guys about, (test drove it, would bottom out over the smallest bumps) but I did pick this one up. Its a 2004, 17k miles, stock except for flowmasters. This is my first svt, so I'm sure I'll have questions later on (did a lot of research, but I'm...

seeing if a pic loads.

i'm really close to buying an 03 cobra, but wanted to make sure i wasnt getting ripped off. (never owned any svt) if the car checks out mechanically, how much would it be worth 03 black 10th anniversary cpe w/8xxx miles pulley/predator/cai/x pipe/catback thanks

Hey everyone, I've been looking into getting a terminator, but wasn't really planning on getting one until later this year (money issues). However, I found a local 03 cobra with 28,000 miles and he is asking for 23,500. I know that normally when I looked at these cars, the owners (don't...

It started a couple of days ago, nothing comes through the vents. I figured look for some kind of fuse issue, but I don't know which one it is. Can someone post the fuse layout, and which fuse it is. Any other ideas or suggestions would be appreciated. Thanks,

So I went to the dyno a couple of weeks ago, and basically could not get a full run in because the car had pinged. It was late in the day, so the shop didn't really try anything. They did give me a pretty good deal, so I am going back. Anyway, I know pinging is a timing issue, but is there...

I'm trying to install an autometer electric oil pressure gauge. I have the power for the lights hooked into my light switch, and have found a good ground. But I can't find a switchable 12 volt source. I took off the lower cover under my ignition switch and stearing wheel, but dont know which...

I just got my boost and oil pressure gauges, but had some ??'s. My boost guage is mechanical, and I know that it needs a power and ground for the lighting to work. Is it supposed to come with the wiring. I have the vacuum tube for it, but it did not come with the wiring for power and ground. Did...

Gauge ??'s So I'm looking into getting a boost gauge and oil pressure guage from Autometer. I've done a search on mech vs electrical, and had a question. If you run a mechanical gauge, on autometer's website they say it does not require a power source, so does this mean that they don't light...

I;ve just finished putting my car back together, and noticing some problems. One of them is that my fan doesn't seem to be coming on. I've run a KOEO test, and when its testing I can hear the fan come on w/both speeds. I had the car running for about 10-15 minutes, and it never kicked on? I...

I finally got my car back together and running, but when I started it I noticed the belt was slghtly coming off the stock tensioner, coming close to teh vortech belt while running. When you turn the car off, the belt looks like it centers a little, but if you start it again, same thing. I was...

Just wondered if I could get some pics on the tenioner on the car. The reason I'm asking is because I can't get the damn supercharger belt on, like its to short or something. I thought that you were supposed to leave that third bolt hole open ( so you could use the aftermarket tensioners out...

I'm trying to run the vortech btm that came with the kit (part #5462) and had a question on the wiring. The kit came with an adapter that plugs in between the coil and factory harness, with 4 wires coming out of it. ( white, red, orange, and black) The wires coming from the btm are white, red...

Is it common to have to cut the discharge tube to fit? Mine looks like its just to long. It doesn't seem like it wants to fit in between the t/b and supercharger even without the rubber hose fittings. I'm pretty sure everything is aligned the way its supposed to be, I don't have pics yet, but...

I'm finishing up my vortech install, and am looking for a place with a dyno. I've called Blood, sounded pretty reasonable to hook it up w/monitoring the air/fuel, but when I asked how much to tune, I was quoted around 1100-1200. That just seems kinda pricey, before I moved up here, most dyno...

Im wanting to do the fox t/b conversion, did the search, found useful pics and everyhting, but I thought x2c motosports sold an entire kit, but there webpage is down and the phone # that I had for them is disconnected. I guess they are out of business? Reason why I'm wanting to do this swap is...

Hey everyone, I've been doing a vortech install but have been taking my time, almost done, but the gas in the tank is from when I started the project...(couple months ago) and wanted to see if there was any other way to get the gas out besides trying to syphon it out. I thought I saw...

Well, I'm basically done with my vortech install, but have some problems. The bracket they use to mount the maf in the fender is for the 94-95 cars that have the flange on the maf, but I already had the c&l 76 maf, which does not have the flange, just uses the rubber hose and hose clamps to...