Search results

  1. TwoToneHatch

    Short Shifter

    I love my Steeda Tri-Ax , But I like the shorter Throws of the Pro 5.0 alittle more .
  2. TwoToneHatch

    Hood pins

    I got a set of Spectre hood pins from a local parts store , they are stainless steel and still look brand new after the past couple months of daily driving . Cost me about $12.99 at Autozone .
  3. TwoToneHatch

    Getting A Fox As A First Car

    A Fox isn't a bad idea for a first car if you want to learn how to work on it and if you respect it . Like others have said be very picky alot of Foxes have been beat to death and back . I held out after looking at a few Foxes and SN95 5.0's and found my '89 GT that was dead stock and in good...
  4. TwoToneHatch

    Misfire/rough Idle , Bad Injector ?

    For a week or so my 89GT has had a rough idle and a decent miss . When you first start driving it , it'll kind of hesitate and miss but if I get on it hard , it'll clear up and just have a rough idle . Well I just threw a set of plugs and wires on it (the ones on the car were a few years old)...
  5. TwoToneHatch

    Front Sits High , Rear Sags ?

    Now that I think about it I don't think I had weigh on the suspension when I torqued down the control arms in the from how much could the ride be affected by this ?
  6. TwoToneHatch

    Front Sits High , Rear Sags ?

    I have stock V8 springs still , I have a set of 4cyl springs in my shed I could use if I feel the need . And the car drives fine with 90/10's and no front sway bar.
  7. TwoToneHatch

    Front Sits High , Rear Sags ?

    I should of specified but I did the front end over a year ago . I made sure the springs went back the exact same way they came out . I have a set of 4cylinder front springs but I have heard that they suck on a daily driver and I have heard that they aren't bad ? The front has a 4 finger gap...
  8. TwoToneHatch

    Front Sits High , Rear Sags ?

    I know these threads probably come up alot but I HATE the way my car sits . When my '89GT was all stock it sat even front and back and looked pretty good . Well I put new FRPP front control arms (used the stock springs) and new 90/10 struts . The rear has lakewood lower control arms with...
  9. TwoToneHatch

    help asap clutch problems

    So your clutch cable is to short so it pops off the quadrant when you push the clutch down all the way ?
  10. TwoToneHatch

    Transmission question

    Well you said the one you can buy is a Tremec , i'd find out if the Tremec is a Z-spec trans(T5Z) if so I would grab that .
  11. TwoToneHatch

    Transmission question

    How much could you get the Tremec ? A rebuild of your will probally be cheaper I'd recommened you have Hanlon motorsports rebuild the one you already have Bob is a great guy to do bussiness with .
  12. TwoToneHatch

    What's the best way to remove pilot bearing?

    Definitely get the pilot bearing removal tool . I got mine with a slide hammer from Autozone and I've done 5 pilot bearings and the tool made it simple .
  13. TwoToneHatch

    It sucks to be me,.....somebodies gotta do it.

    That was one of the best posts I read in awhile , good thing you got most of it squared away it'll be fine when your done with it .
  14. TwoToneHatch

    Best Short Throw?

    Can't go wrong with the Tri-Ax I put mine on the day I did my AOD to T5 swap and love it .
  15. TwoToneHatch

    What cam goes best with gt40p heads?

    TFS Stage 1 is cheap and would work good or like others have said stock cam with a 1.7 Rocker for more lift .
  16. TwoToneHatch

    No Brake Lights Until Pedal Is All The Way Down

    Alright wasn't sure if there was any kind of adjustment since it still kind of works , but I'll check it out .
  17. TwoToneHatch

    Rear Control Arm Install

    Thanks everyone , and the ratchet straps are a good idea I have have a couple sitting in the shed I can use .
  18. TwoToneHatch

    No Brake Lights Until Pedal Is All The Way Down

    Just like the topic says I have brake lights but not until the pedal is all the way down , anyway to adjust this ?
  19. TwoToneHatch

    Rear Control Arm Install

    The uppers are adjustable the lowers are not adjustable .
  20. TwoToneHatch

    Rear Control Arm Install

    I got a set of nice upper and lower control arms I want to put on my GT , never did it before anyone so how do I go about it ? Also would I be better off welding the seams on my torque boxes or buying one of the torque box kits of LRS ?
Top Bottom
Back
Forums
Menu