Search results

Hi, I need some help putting my wipers back. In what order do the two washers go in relation to the short wiper motor output arm? I know that the nut with built in washer would go on the end to hold it all together, just not sure about the other two parts. Thank you

Stangnet, I have a considerable amount of dirt and sand in my frame. I was considering shooting high pressure water into the frame and the area where the transmission mount bolts into. I felt moisture in the dirt I was able to pull out so I do not want to leave it in there but I am concerned...

Does anyone know what this is and what it does? My baggie is labeled as from the windshield wiper mount. I took this apart like 4 years ago and do not recognize what it does. Thanks for your help.

Hello, for those of you from the SF bay area, what transmission shop do you recommend to rebuild a T-5 transmission? Thanks for your help.

Stangnet, does anyone know what this button/mount with a white bushing and clip is for? I also wanted to ask what the rubber bump stop for the brake pedal is called, or what homemade replacement was used. What have folks on here used to make a bump stop for the clutch pedal? Thanks for...

My passenger windows are showing dried out rubber bulging out of the lower end of the frame. Do local auto glass places take care of the rubber between the glass and the frame if you have them replace the glass? The trim on that goes from the top to the back of the window is scratched, is it...

I am getting closer to getting most of the parts to take in a F4TE block to be built into a 408. I plan on getting some type of serpentine pulley system and a high flow aluminum water pump. In regards to a 1967 Mustang, what are the pros and cons of having the water pump inlet on the...

My hunch is that my single plane 351W Vic Jr. Intake is too high RPM for a 60% street driven vehicle with 3.89 gears. The other 40% I would say would be spirited mountain road driving. What would a Wilson Manifolds 1 inch 4 hole tapered carb spacer do to this combination? :D

Stangnet, I am in the planning stages of deciding what gauges to get. I have seen some members here use Speed Hut in their 65 Mustangs. Has anyone installed them in a 67 Mustang? Pictures would be awesome if they are available. Thanks Everyone.

Stangnet, I will be installing brake lines in my car soon and I am trying to figure out what to order. What is recommended stainless or steel brake lines? I have Wilwood discs in the front and rear with braided stainless lines that will connect to the brake lines. Would I order the...

stangnet, I intalled some new disc brakes and the outer pad fits snug. Is this normal? My guess is that if I drive them a mile they will settle properly. I have about 1.5 mm on the inner board pad but the out board one had to be pushed in. Thanks Armando

I needed some advice on a roller 351W. From what I could find these are supposed to have a compression ratio in the high 8's. From the factory they had the E7TE heads. What combustion chamber size do these heads have? If I get one of these stock engines with 80K miles can I install 58cc...

Hello everyone, I did a search and did not come up with an answer. I am using a Ron Morris T5 cross member on my car. I bought and Energy Suspension urethathane mount and it does on fit. The urethane mount is for a fox mustang with a T5, was I supposed to purchase one for a 67 Mustang with a...

I would like to ask if anyone has the instructions to install GW upper control arms? I can not find the instructions and this weekend is one of the few times I have time to install them. I checked their website and they are not posted, if anyone has them please post here or e-mail them to...

Hello, I just had my car painted and I am trying to figure out the correct color for the thin grill material on the fastback vents. They are currently white, but want to make sure that it is the correct color before I ask the paint guy to spray it. It is shaped like the vent and is about 2mm thick.

I want to set up an engine with low 10:?:1 compression ratio and fuel it with 91 octane. Is there a benefit of using a 331 stroker engine kit with dished pistons and smaller volume heads as opposed to running flat or domed pistons with larger volume heads? I have been wondering this for a long...

Hello everyone, I wanted to get some input on the Edelbrock Pro Flo XT PN 35273 from the EFI experts on here. Is it worth the $3400 to go Edelbrock EFI or are there other EFI systems in that price range that are less $ and just as good? Thanks for your input.

Stangnet, the feedback received in the classic section on engine questions has been extremely helpful. I am looking at a Ford Racing Engine that has a good power rating and was built with great parts. It is noted as a sealed crate engine and only see it needing a change of oil pan to work...

I am have been looking into Crate engines and came across a ford racing 347 crate engine that uses a BOSS block and forged internals. It retails for about $8,600, it looks fairly complete and just needs a carb and a front sump oil pan to run in a classic Mustang. I wanted to get some...

Hi, I wanted to ask if anyone has done business with M&R Engines on ebaymotors? They have good feedback but just wanted to see if anyone here has installed an engine in their mustang and had it long term. Just trying to make the best purchase possible for a 5.0L based 331 stroker. Their...