Search results

I inherited my sons 2002 GT after he passed away and tried driving it and it ran ok till I tried to put it in 3rd or 4th gear, would not go in, what could cause this ? I am assuming the synchros are bad but was wondering if there could be something else I could check before pulling the trans...

I inherited my sons 02 Mustang after he passed away and am trying to get it cleaned up and found these 3 wires without a connector, can someone tell me what they go to ? 2002 Mustang GT with shaker hood. I've never worked on a 4.6/ 5speed before so any help would be appreciated.

I installed a new heater core over the weekend and now the power locks don't work, I unhooked the wiring under the pass. side kick panel and re-hooked everything I think, I do have an alarm system which connects under the drivers side kick panel and I could have damaged a wire there also since...

Getting my 1st 347 built and I don't know if I should go with stock oil pump or high volume, I'd like opinions from others that have had 347s. Are there any parts needed for a 347 you would recommend, this is a cruiser and NOT a racecar, not looking for 400 hp, just a dependable engine. Thanks

I ordered a 347 short block with a TFS stage 1 cam to put in my 90 GT, I have a set of TFS 170-58 heads with 1.6 rockers, 24lb injectors and mass air. The car has an AOD trans with a saturday night special convertor and 3.73 rear gears. I do NOT plan to race the car, its a 1 owner car that I...

How much HP will 24lb injectors be good for? I already have 24lb injectors and mass air meter, a 65mm TB and an explorer intake and am looking to get another engine because I am starting to get lower oil pressure after the engine warms up. I want to keep it fuel injected rather than switching to...

I am planning on replacing the brake lines on my 90GT and dont see how the proportioning valve mounts to the car, I replaced the brake line that goes back to the rear axle and had a hard time with getting the line loose and figure it might be easier to just remove that one and cut the other...

I bought my wife a 2007 V6 mustang and she wants the GT style grille, will the GT grille fit on a V6? I have seen AM shows different grills for the V6 and GT but don't know if they are actually interchangeable or not.

Brakes are acting like manual brakes so I am going to replace the power brake booster, any tips on how to make this easier and save some time? I replaced the master cylinder last week so the brake lines should come off easy so I'm not worried about them, just on getting the bolts out under the...

I will be installing a TFS stage 1 cam on a 5.0 block with TFS heads, the car has an AOD trans and seemed to lack a bit of low end power with the cam installed dot to dot, should I install it with 2, 4 or 6 degrees advance to gain more low end torque, not a race car..just daily driver-cruiser...

I have a set of TFS 170 heads 58cc and stage 1 TFS cam, 24lb injectors and matching MAF, and an intake from an Explorer........I am going to replace the shortblock because I am losing oil pressure after it warms up now and I am not sure if I should stick with a 302 or go up to a 331 or 347. I...

I was driving my 90 GT to work this morning and when I got off the freeway my headlights started going off and back on, I switched to the high-beams and they worked fine. It started when I had used my turn signal so I assume the switch is going bad and needs to be replaced but I'm also wondering...

Finally redoing my interior, seat upholstery, headliner,sun visors, and carpet.........I started taking everything apart and have it all apart except for the latch for the sunroof, it should be just 2 nuts that need o come off but the bolts are spinning, they have round heads and there is no way...

I have TFS 170 heads and stage 1 cam, I'm looking to upgrade my intake with something better than the current Explorer intake. I have 24lb injectors and matching MAF , looking for what would be a good replacement for a daily driver type car, I'm not racing it. Anyone have any experience with the...

I am interested in buying a 07 Mustang and was wondering if anyone could check carfax or any of the other VIN # check sites to see if the car has been in an accident, been in a flood, or had anything else bad in it's history. The VIN # is 1ZVHT80N075274880 if anyone can help.

My 90 GT needs the A/C working again, I had to remove the condenser when I installed the cam and heads and would like to refill the R-12 but I don't know if any of the other parts should be replaced before I recharge the system. The system was open for a couple days when I did the cam/heads and...

My sons car starts and runs good for about 20 mins and then the Idle goes up between 2-3000 rpm, what could cause this? Checked the codes and he got , 81, 82, 85, 84 & 95, With 34 in memory.......the car has had all the emissions stuff removed and he is changing the EGR out now with another one...

OK, I got my engine all put together and it runs good but I can only get it to 12degrees and want to move it up to about 14, but it hits on the water neck and won't go any further. I want to pull the distributer and move it one tooth over to get a little more room for adjustment and I am...

I have read that to set preload on stud mount rockers you set at zero lash and then go 1/2 , 3/4, or a full turn. I am wondering which is better and why, what are the pros and cons of one over the others? I have a stock bottom end and just put a set of TFS 170 heads and a TFS Stage 1 cam, I went...

I put a set of TFS heads and a cam in my engine over the weekend and now I have some water coming out the exhaust. The heads were new and the block was clean, I put teflon tape on all the head bolts and put RTV on the lower bolt threads also. On the intake I only used antiseize on the threads...