Search results

I would like to replace my rear control arm bushings but all I can find are polyurethane. I have read that without reinforcing the control arm to body mounting points polyurethane bushings can cause damage.Next summer I am going to go through and reinforce everything and replace the control arms...

(87 GT) Napa lists only UCA bushings I was wondering if they are the same as LCA. To axle and to frame are listed for upper but nothing for lower. If someone could clue me in I would appreciate it. Thanks for the help.

(12/86) '87 GT 5-spd orig blk paint and body panels/bumpers never in an accident not lowered the car measures square.New = (susp. bushings, steering rack, pwr str pump, shocks, struts, strut mounting bushings and 225/50-16 BFG Sports)fct. strut mount plates. Took it to Truline Frame and Wheel in...

EFI to carb swap weiand stealth, 600 afb, '87 GT 5-Spd Oil spraying out of dipstick a small amount but enough to coat the steering shaft and side of the strut tower, I was getting condensation in my oil and on the dipstick so I installed a PCV valve(between the tube by the oil fill neck and...

port and polishing my heads I am wondering if it is ok to remove the small bump on the top side of the exhaust runner about 1/2 in from where the exhaust exits the heads. It is almost a 1/4 in in height and would definetly improve flow if it was not there, I dont know if this is part of the...

I might have a head gasket leak (milky looking crap in oil and out of breather tube I just changed T-chain and water pump so ther is a small chance that water is getting in the oil from those gaskets there is no water leak around T-chain cover or water pump I used a small amount of RTV gasket...

I am installing a Pro ripper shifter It does not have a shifter ball bushing with it. I have been trying to find one Ford and Napa cannot get it ford says they dont make that part individually anymore. I would like to replace it but cant seem find one. Thanks for any part #'s or places to go.

I am going to replace Ball joints and Control arm Bushings on my '87 GT at home if possible, I have a bench vise and sockets. I was wondering how anybody else has done this without a press. Thanks in advance for any suggestions.

Sorry for the double post how do I delete this thread

Replacing T-chain on my 87 stang tommorow just wondering if I need loosen up the bolts or drop the oil pan at all. If so can I let it rest on the crossmember. I have Oil pan gaskets just in case. Thanks for the info, I would rather push a Ford than drive a chevy any day!

Whats up guys, I have a 1999 gt-40 crate w/ B-303 cam, 1.6 svo RR, and svo aluminium heads I know on these early versions FRPP put the heads and cam on a factory long block, are the valve springs they put in these good, I have been reading about valve floating problems around 5000 RPM's is this...

BBK fuel pressure guage and adjustable regulator BBK/WALBRO FUEL PUMP 255ltr/hr. works great $100 DOLLA no lower

How do I delete this thread ??? how do I delete this thread??????

Need help getting temp and oil guages functional after E.F.I. harness removal. Do I tap in to one of the two plug in connectors black and gray(with several cylindrical terminals) from driverside harness left after efi removal.How do I Identify the wire for guages. Should one of these have power...

Whats up? I have an 87 GT that I am converting to a carb set-up for track use of course. My question is this, what are the holes on the rear of each cylinder head for and is it ok to plug them or should the be recirculated to the exhaust. Thanks for your help!!!

Hey, new to the site Mustangs are great I have an Black 87 GT 5spd that I am swapping to carb before Installing gt40 crate engine. I have been doing body work on cars for the past ten years and am capable of taking them completely apart wrecked and putting them back together looking better than...