Search results

  1. cobra1540

    A-arm bushing removal tool

    I was reading your pm's and replying to you that way (last night), as I said I don't know if you received any of them before I posted the link in your thread. If you didn't, then I suggested you go to a machine shop, body shop the dealer (if you know anyone that works at one), a spring shop...
  2. cobra1540

    A-arm bushing removal tool

    I don't know if you received my replies or not. Here's a link to the directions if you didn't.http://www.steeda.com/directions/122-4-3140_a_arm_bushings.pdf
  3. cobra1540

    A-arm bushing removal tool

    If you are referring to rubber bushings Take a drill with a 3/8" or so drill bit and drill as close to the outside as you can, push the bit all the way through, then reverse the drill and it should walk its way around the outside. You may still have to hammer the bushing out, but it should be...
  4. cobra1540

    Mustang on 30's

    That's wrong on so many levels. Just because something can be done, doesn't mean it should be done. :ban::ban::ban::ban::ban::ban:
  5. cobra1540

    is it really this slow?

    If you put the car in park rev the engine to 3,000 or so ( not much higher ) . Let off the gas and you hear a knock as the engine returns to an idle, you have a bad rod bearing. If it knocks only on a cold start, you could have a collapsed piston (skirt). With the engine off pull your intake...
  6. cobra1540

    Mustang Stereo Question

    Those are ILS rating on the stereos. If Lightning Strikes. There is some other problem if that is draining your batt. Do you mean it sits for a week and won't start or the head lights dim when the bass hits?
  7. cobra1540

    One Sneaky Picture

    How much do you want for the box? What's it worth in the Qtr.?:stick::shrug::rock::banana::banana:
  8. cobra1540

    distributor leak

    Does your distributor have an o-ring on it?
  9. cobra1540

    93 GT or Cobra?

    Ford didn't make a 1993 Cobra convertible.
  10. cobra1540

    91 lx notch 5.0 swap help

    Yes it will bolt up, but the axles are a little longer on the '95 (disc brakes). I'm not sure how much longer, maybe 1" or 1 1/2". I believe you can switch to drivers side ranger or bronco II axles. You'll have to do a search for that, or go with different rims ( backspacing ).
  11. cobra1540

    Want to hit 12s in a relatively stock stang

    My dad and I are working on the same thing as you are SDGT with an '88 coupe. The only mods to the engine are 65mm TB, meizer electric WP, electric fan and CAI. We're running 4.10"'s this year, on MT ET street radials (255-60-15's) with a best times : 1.82 - 60' , 13.34 at 102 mph. Last year...
  12. cobra1540

    Rocker arm slipped off, GT40 heads

    It sucks you've got to machine the pedestals, but this should cure any future issues.:nice::D
  13. cobra1540

    Bad Idle Surge on '88 Fox w/Mods

    liljoe07 - I agree with what you're saying. BTW - these numbers are from the ford fuel inj. manual written By Probst At 86 degrees F. - 2.62 volts or 24.27k ohms 122 -DF - 1.72 v. or 10.97k ohms 194 DF - .61 v or 2.8k ohms 212 DF- .47 v...
  14. cobra1540

    Bad Idle Surge on '88 Fox w/Mods

    liljoe07- I understand what you're saying about the code 21 and ambient vs. operating temp. I've never seen that be the case before, but just because It hasn't happened to me doesn't make it untrue. If dangrego gets his engine up to operating temperature and then checked the sigrtn wire at the...
  15. cobra1540

    Bad Idle Surge on '88 Fox w/Mods

    No, I didn't see the picture of the way he has it mounted before I posted. All I'm saying is If the coolant is at ambient air temp, the act and the ect sensors should have the same resistance as measured on an ohm meter. Just to clarify the 2 resistance measurements were taken at the prongs on...
  16. cobra1540

    Bad Idle Surge on '88 Fox w/Mods

    I'll check back tomorrow.
  17. cobra1540

    Bad Idle Surge on '88 Fox w/Mods

    Then it's not the fault of the sensor is it, but the wiring. How can you mount an ect sensor wrong?
  18. cobra1540

    Bad Idle Surge on '88 Fox w/Mods

    I'll be back on tomorrow afternoon. I need more info . What your telling me is too vague? You need to check the sensors when the coolant is at ambient air temperature, from what was posted i thought you did.
  19. cobra1540

    Bad Idle Surge on '88 Fox w/Mods

    What new computer? How could you hook it up funky? What was the code ? ????? Has what mounted?
  20. cobra1540

    Bad Idle Surge on '88 Fox w/Mods

    I figure it to be ~ 4%, they should be O.K.