Search results

  1. bmo37

    Overheating With Ac On

    Its not as easy as people think, basic little things you can do are pretty easy but to do it right you need a dyno ortherwise you must invest in a wideband o2 and log than as well to make any progress. The ford eec strategy is literally as thick as a bible and alot to take in. Also I would opt...
  2. bmo37

    Overheating With Ac On

    Its accurate I log tems on my tweecer when i tune.
  3. bmo37

    Overheating With Ac On

    I've batlled my fair share of overheating issues but this summer I've ran into an overheating issue that has me pretty much stumped. The car at this point has a new high flow water pump, new alumnin 3 core radiator, dual ford contour electric fans, new thermostat and cap, new hoses, system has...
  4. bmo37

    Engine to Bell Housing Block Plate

    Thanks for the reply Rick, guess im going with the new plate.
  5. bmo37

    Engine to Bell Housing Block Plate

    Has anyone run their car without a block plate in between the engine and bell housing? Pretty much tore the car down to redo the rear main seal and check to see what was causing excessive chatter on the clutch. Sure enough it wasn't the clutch itself rather my flywheel weight actually wore a...
  6. bmo37

    Car is running cold... been through 2 stats. Help?

    sure your sending unit is working right or the gauge is accurate. I actually have the opposite problem I run overheating under load or cruise. I would verify temps some other way like an IR heat probe gun. Could use under drive pulleys to slow the water pump hence making it run hotter and not...
  7. bmo37

    if you had $300???????????

    weld in subframe connectors and spend the other hundred on a hooker :)
  8. bmo37

    Manual steering, do you regret it?

    Pretty much my brother and I have identical cars except for he's drag setup (welds/skinneys, manual rack, k-member, etc) mine I designed to be a street setup (ac/all emissions/power steering). The comparison is night and day in terms of drive ability. I absolutely hate driving his car as stated...
  9. bmo37

    A/C help please

    Just did mine over as well, I replaced all the system o-rings, got a new accumulator, used the 10 dollar harbor freight vacuum pump to pull vacuum for about an hr, vacuum tested the system for 30mins. Did a oil charge, leak sealer charge, 2 3/4 cans of freeze 12. Works great spent a total of...
  10. bmo37

    Bad Fuel Pump: Any suggestions before buying a new one?

    Personally I would get the 255lph hp pump since we have return type systems so no fuel is ever wasted going smaller can only hurt i the future.
  11. bmo37

    No Dash Lights, Fuses are good, Running taillights work.

    I concur the dimmer switch or your have a short feeding the circuit check for 12 volts on the light blue/red striped wire connected to the fuse panel.
  12. bmo37

    Intake Manifolds

    For the budget racer the typhoon intake is the best bang for the buck out there, I still have mine and it's still going strong, anyone that's ever owned one knows their actually good intakes to port despite the casting flash and clean up work, the runners are actually pretty thick, but it gets a...
  13. bmo37

    MAC or Flowmaster?

    Hmm interesting I was acutally going to go with a new set of mac 3" because I thought they would be easier to install and read they fit well. I know over the years I went through sets of there headers, prochamber mid pipe, offroad pipes and the fit was middle of the road.
  14. bmo37

    When to ditch the PCV system?

    Yeah I'm in the same boat I researched this topic alot and there are handfulls of different methods but all of them are usually generalized in the sense they work or do to some extent but with side effects. I read of people running -10, or -12 weld bungs with stainless hose to a breather catch...
  15. bmo37

    When to ditch the PCV system?

    Never really thought about it but what would be a good threshold to switch over to a catch can evac setup versus the stock pcv system. Is it applicable with low boost setups 7lbs or less, does it apply for larger cubes or just higher spinning motors? I know in my case I'm looking to go this...
  16. bmo37

    Idle

    15 is nothing 85 is the canister purge solenoid 66 MAF failure (probably whats wrong as your car is running in limp mode) 96 Air diverter valve circuit failure The big one is the maf, I would clean the sensor wire in the maf and the pin connetors with a qtip and rubbing alcohol. If you Maf is...
  17. bmo37

    Newb to modding 93 cobra suggestions

    Personally I wouldn't touch a thing on a 93 cobra, I would buy one of millions of other foxes out there to mod but thats just me and I'm nostalgic.
  18. bmo37

    QuarterHorse vs. AMS PMS

    This guy is 100% right in his accessment. I've been playing around with tuning for a couple of years now and you really need to be deticated to learning it. I've read the ford eec epc manual about 20 times, the aem tuning guide, both tweecer and eec analyzer/be manuals and follow all the forums...
  19. bmo37

    TWEECER NEED?

    I run the tweecer rt with eec and bin analyzer as well. The latest one is the moates quarter horse which seems to be a nicer option as you can change parameters on the fly without having to shut the car down and back on. Either way I reccomend going with eec and binary editor over the free cal...
  20. bmo37

    GT to LX tail light swap

    I just bought the lens covers and a new weatherstripping kit from 50resto. Yanked the old one off and put the new ones in its place with the stripping and clips.
Top Bottom
Back
Forums
Menu