Search results

I bought the car used so it didnt have the manual when I bought it

I was originally going find a seatbelt end at a junkyard and just put that in it...lol I just would like to meet the geek that took the time to figure that all out...lol

Thanks but I just heard an easier way to deactivate that chime. You have to jump through a few hoops to do it but it works. Here is the other way for anyone that might need this info: Step 1: Turn ignition switch to ON. All the way forward without cranking the engine. Step 2: Wait...

I have a 2000 mustang. Where can I disconnect that annoying seatbelt chime that keeps going off until you put your seatbelt on? Yes, I know it's law to have one on but regardless, I would like to know how to disconnect it. Would there be a harness under the driver seat or something? I could...

Well, the problem was the connections on the switch were on the wrong terminals. It's a lighed rocker switch that had been installed. One wire was going to the POWER terminal and the other one was going to the GROUND terminal. It should have been one on POWER and the other on ACCESSORY...

On my '00 V-6 mustang, the previous owner installed an aftermarket shifter handle, which meant he had to mount the o/d switch to a different spot using a toggle switch. My problem is that I just noticed that this switch he rewired does not work. It does not lockout the overdrive, nor does the...

I was also told it could be a blocked evap line at the fuel tank or a bad charcoal canister. You guys might want to check that out as well.

Recently bought a 2000 mustang(V-6) but everytime I go to put gas in the tank, the fuel nozzle handle keeps clicking(as if the tank is full). I have to let the fuel trickle into the tank and even then the fuel nozzle wants to "click" off. It takes 5-10 min. to put $20 worth of gas in. I've tried...

Around here, you won't touch an 8.8 for less than $250 or a T-5 for less than $150(bad syncos or not). When I was looking fo ran 8.8 for my '82 I couldn't find one for less than $275 and that was stock gears with worn clutch packs. It's harder to find older 5.0 parts because the junk yards are...

Wow..$250...that's it? I don't know about where you guys are from but around here you can probably get $500 for it if you took it to a recycle/scrap yard. The reason I asked this question was because I actually sold this car for $800 and my lowest offer was $600. I guess I made out on the...

1988 mustang GT, 5 speed (all stock) with 130k miles. Here is what's wrong with it: wrecked front end (needs both fenders, hood, whole front nose clip) frame is not bent or rusted. Second gear syncro needs replaced No heater and fuel gauge does not work Interior is fair condition Tires...

Got it! It turned out not to be the bulb after all. The ground wire to it brole off its connector. I put a new slide connector on it and was done! DJ fury, for future reference, what all is involved in replacing the high beam? It looks like some disassembly is required for that...

Trinity, I think the link to the bulb you posted is for the actual halo itself. What I need is the low beam, which actually is in the center of the halo. I believe DJ fury solution is going to be what actually needs to be done in my situation. I will find out in a little bit here and let you...

Low beam on passenger side.

Cool...thanks! I'll give it a shot after work tomorrow.

I did not see a ballast anywhere or any extra wires running over to the battery so it might be safe to assume they are an H1 bulb. I guess my next question would be: how do you remove/install these bulbs? It doesn't look like the typical setup where you twist a plastic ring and pull the bulb...

Their bulbs are selling for $70 each!! I doubt I will be buying two at a time. I'm thinking it might be a 9007 bulb type, like the OEM's are, except it's a HID bulb. I'm just wondering if these HID bulbs can be bought at a local auto parts store for less.

Ok, I looked at the assembly and found they are made by Junyan, who I never heard of before, but anyway, I went to their website and they make replacement bulbs but they sell so many different replacement bulbs that I don't know which one I need. I send them an email asking which ones I need...

You haven't even seen what I have so how can you say they are cheap and ugly dickhead? trinity GT...if I had the make and model number I would provide them but I dont because I bought the car with them already on. I was hoping that maybe someone on here might have bought a set and installed...

Why would I want to go back to the inferior OEM lights that suck? If I'm going to do that, then I may as well get another set of aftermarkets that look and perform better than OEM and probably cost just as much. The sad part is that I've asked people how actually HAVE these Halo lights on...