Search results

  1. F

    Tx Locals, Brazoria

    I'm a NY native that just relocated to southern Houston area. What are the emissions requirements? what I viewed on TX inspections site was very vague... Refers to a visual inspection in one part and a sniffer in another... Which one? both? I have an after market exhaust that past westchester...
  2. F

    cross drilled rotors cut in North NJ or South western NY

    Thanks for the input. So nobody up in the NYC surrounding areas has any luck get slotted/drilled rotors cut? This is for a '00 R brake set up. The two set of rotors I had worked very well, but I run through pads on these. I wouldn't wanna match $120+ pads with cheap rotors, kinda defeats...
  3. F

    2000 Cobra R front Pads

    Thanks for the replies. I had seen the Hawk HPS 570's would fit the application but wasn't sure how they would behave on the street. The original brembo pads worked very well with out having to be heated up very much if at all, they STOP quick even under normal driving. The statement about...
  4. F

    cross drilled rotors cut in North NJ or South western NY

    I'm looking to find a place that will resurface/cut cross drilled or slotted rotors in Bergen county NJ or Rockland/Orange/Westchester county NY. Alot of places won't do it as they fear it'll wreck the bits on the lathe machines. If any one has had success getting them resurfaced in that area...
  5. F

    2000 Cobra R front Pads

    I'm installing a brembo 2000 cobra R front brake set up on a 2003 Cobra. I know the size/part is the same as a standard 13" cobra rotor, but the pads are different. Does any one know the ford part # for the brembo pads? Or does any one know the dodge part # for the same pads? I do know that...
  6. F

    Maximum Motorsports Adjustible rear swaybar

    here is the link to the specific kit Adjustable Rear Swaybar, 3/4 solid bar, bolt-in kit [MMRSB-3] : Maximum Motorsports, the Latemodel Mustang Performance Suspension Leader!
  7. F

    Maximum Motorsports Adjustible rear swaybar

    MM Adj rear sway bar, for 79-04 solid axle. Not IRS. 3/4 inch, bolt in kit. New in box. Was purchased for a 2003 GT but never installed. asking $ 250 or best offer.
  8. F

    TA rear end girdle/cover 8.8

    sold
  9. F

    99-04 forged axles, 8.8 31 spline new in box

    sold
  10. F

    99-04 forged axles, 8.8 31 spline new in box

    axels pm sent
  11. F

    aluminum driveshaft 99-04

    sold
  12. F

    aluminum driveshaft 99-04

    sent you a pm
  13. F

    aluminum driveshaft 99-04

    Aluminum driveshaft out of 2003 GT, used. excellent condition. Comes with 1330 slip yoke and ujoints. Was used behind a stock tremec 3650. Ford Racing Performance Parts - [Part Details] asking $150 make me an offer. located in 10992
  14. F

    TA rear end girdle/cover 8.8

    New in box, never installed. TA performance 8.8" high strength differential girdle/cover. Forged aluminum. This will clear an aftermarket panhard bar on a 1999-2004 mustang gt. Has bearing pre load bolts, complete kit. make me an offer. Ford Girdles | TAPerformance.com asking $ 100
  15. F

    99-04 forged axles, 8.8 31 spline new in box

    New in box, never installed. Alloy USA forged axels for 8.8", 31 spline. Will fit 1999-2004 ford mustang, not cobra. Paid over $200, sold car never installed. Comes with seals seals, bearings and studs. Make me an offer. asking $150 Part # 12187 AlloyUSA - GM Ford Dodge Rear Axle Kits...
  16. F

    rear end shop in orange county NY

    Does any one know of a good shop to assemble a rear in orange county NY? I already have all the parts was goin to do this myself but project repeatedly delayed by home responsiblities. 31 spline Differential, gears, axels, TA cover, aluminum drive shaft and weld tubes. I live in...
  17. F

    FE engine/block Id

    so it would be right above the starter? like on the 427's? thanks, dave
  18. F

    FE engine/block Id

    428 ID? The guy sent me a pic of the block, diffinately no crossbolts above the pan rail. Couln't make out the part #'s though. I'm gonna go take a look this weekend any way. Are the casting #'s for a 428 (390's as well) in the same location as the 427's? Just for block ID. Thanks for the...
  19. F

    FE engine/block Id

    This guy nearby has an FE engine he claims is a 427. How do I confirm this if the engine is assembled and missing the engine tag? I believe the part #'s aren't visible from the outside. If the engine is in pieces (which it may be) where are: the casting #'s on the block? (I read somewhere...
  20. F

    toploader interchange

    thanks for all you info guys. much appreciated
Top Bottom
Back
Forums
Menu