Search results

  1. Y

    t5 how much?

    How much should i expect to pay for a used t5 transmission now days?
  2. Y

    car stalls at idle after about 2 mins

    I am embarised to say that it was my msd ignition (6AL) do to the fact that i tested it before. but i am glad to say im back up and running. THANK YOU for all the help. to anyone reading this, the cranks ok but does not start checklist really does work. expecally if you start at the top of the...
  3. Y

    car stalls at idle after about 2 mins

    I just ran codes with the car running and got codes 41, 91 and 34. I have to wait about 3 or so mins before i can restart. If i try to restart the car right after it dies it will just crank, but not start
  4. Y

    car stalls at idle after about 2 mins

    I had the old tfi tested 3 times and it was good so i thinking it was the pip so i bought a new tfi msd distributor(only 1 day old). Still the same thing. I ran the codes and got codes 34, and 85. Both the egr and carbon canister have been removed. the egr has been removed because my heads dont...
  5. Y

    car stalls at idle after about 2 mins

    The car dies both with the spout in and with it out if that helps any.
  6. Y

    car stalls at idle after about 2 mins

    I have a 92 Gt that has been sitting in the garage under going an engine rebuild for a few years now:notnice: when i start the car it stalls after about 2 mins when just idling. I have replaced the coil and distrubutor(both msd). i disconected the msd ignition (6AL) and the car still does the...
  7. Y

    Mark VIII Fan 97-98

    I know the Mark VIII 93-96 models are three wire and the fan speed changes based on which black wire you connect. The Mark VIII fan for 97-98 models are two wire. My question is how do I change the speed of the 97-98 model fan or is this a two speed fan.
  8. Y

    high beam indicator

    When the key is off and i turn the headlights on, the high beams, low beams and flash to pass all work. But the high beam indicator does not come on... When the key is in the on position the high beam indicator stays on weather the lights are on or off. NOW MY QUESTION IS WHAT IS CAUSING THE...
  9. Y

    Turn signal help

    I also have a 92 Gt and had this same problem. First check the #5 fuse and see if it is blown or not. If you don't know which fuse is #5 then check and see if your reverse lights work. If they work then the fuse is good. The problem will be your turnsignal switch(turnsignal highbeam and...
  10. Y

    Turbo mounting question

    NO, on the setup im talking about the turbos are mounted on the tail of the headers!!!
  11. Y

    Turbo mounting question

    bump
  12. Y

    Turbo mounting question

    I know its not commonly done there and that there is next to no room there but i have seen it. I belive there was a short extention from the header to the turbo and about 6'' were cut off the h-pipe.
  13. Y

    Turbo mounting question

    Does anyone have any info on doing a twin turbo setup where the turbos are mounted under the car where the headers and H-pipe meet.
  14. Y

    Which model t56 for t5 t56 swap

    which t56 works best for the t5 t56 swap in a 5.0, or does it matter which model you use for the swap:shrug:
  15. Y

    t-5 to t-56 swap (what do i need)

    What do i need to go from a t-5 trans to a t-56 trans??? do i need to change driveshafts, get the driveshaft cut, or just change the input shaft??? Can i use my same clutch or do i need one that is a different spline??? And lastly does anything need to be done to the crossmember like on a tko...
  16. Y

    347 engine wont start

    if you have stud mount rockers make sure they are adjusted right. this may be the cause of the poping you are hearing!
  17. Y

    Starter problem

    when i start the car the starter won't stop cranking unless i disconnect the battery cable. ignition switch is good. the starter relay is good. had the starter test and it was said to be good. what could it be?:shrug:
  18. Y

    trouble turning block by hand

    timing chain gear was put on backwards and got caught on the cam thrust plate bolds not alowing anything to turn!!!! :nono: i relised my mistake when the thrust plate broke while using a 1/2'' ratchet!!!!!:jaw:
  19. Y

    trouble turning block by hand

    im trying to install stud mount rockers. in doing so i am turning the block by hand with a 3/8 ratchet, brakerbar, 16mm socket, and a 12'' extention. so far i have broken 2 craftman ratchets( not inhalf but the ratchet startes to slip after i put so much presure on it) and a 1/2 to 3/8 adapter...
  20. Y

    incon twin turbo kt

    does anyone know where i can get a incon twin turbo kit or atleast the headers for the kit
Top Bottom
Back
Forums
Menu