Search results

  1. R

    65-73 351W Complete Exhaust

    This is the exhaust from my 67 Mustang with a 351W conversion. The headers are JBA Chrome Mid Length (pt # JBA-1653- $499.00 New). The entire exhaust is still currently welded with the only exception over the back of the wheel wells where I cut the straight portion to pull out from under the...
  2. R

    LOTS of parts FOR SALE in ARIZONA

    What type of rearend do you have and with 4 or 5 lug and what gears? Dave 623-203-5901
  3. R

    Need help with wheels/offset Welds for my 67

    I am getting a set of welds for my 67. was wondering what anyone has run with welds. Looking at 15X8 with 4.5 backspacing and 15x4 with 2.5 back spacing for the fronts. Also whats the biggest rear wheel, was hoping for 275/60-15 with any luck. Running 17" bullets now with 275/40-17 and it...
  4. R

    Magnum 500 with New CAPS of a 66

    Where are you located. I am in Phoenix. Why the problem with drums, they came on some mustangs with droms...I thought. Anyway, I have 17 X 9 taht fit my 67 with spacers but I rub on bumps with the fender. Thanks for any information.
  5. R

    will 18 x 9's fit up front on a 67 stang

    wheels NO! I have a beautiful set of wheels that size that looked sweet and seemed to be alright with not one but two spacers to clear the control arm and steering link. None needed in rear except to balance the stance from the front. Then I dropped my motor in and the front wheels wont turn...
  6. R

    Need help with headers

    I have a fresh 351w I just dropped in my 67 mustang project. Can't find any headers for the 351W. The 289/302 headers bolt up to my heads, but their to short with the taller deck. I have AFR aluminum heads if that matters. Will post pics as soon as I can get them to upload:( Thanks for any...
  7. R

    E6AE Heads, anyone know the specs

    Your right Thanks for the info. Your right, they were at best a substandard head and as far as performance, there was none. Rumple 69 :spot:
  8. R

    E6AE Heads, anyone know the specs

    Looking at a pair of 302 heads with E6AE casting numbers. I think they are the 64cc chambers, not sure on the valve size. Any info would be appreciated. Rumple 69
  9. R

    Help with roller motor set up

    I took the roller motor from my 89 5.0 (EFI) for my 67 coupe and did a rebuild on the short block. Standard 306 set up. Want to keep the roller motor with the edelbrock intake and 600CFM carb. Heads are ported stock but flow above GT-40's. Question is what cam have any of you used with a...
  10. R

    What type of fuel pump

    What type of fuel pump I have an 89 roller 302 block. Can I use the different cam cover from an older 289/302 that has a place for the fuel pump to mount. Or...do I have to run an electric fuel pump from the tank in my 67 coupe. Didn't know if you could even run a manual fuel pump on a roller...
  11. R

    VIN information

    I just picked up a 289 and c4 for my 67 coupe. Motor is a 2 brl. ID tag on intake manifold is 289 65 5 and at the bottom right it has A561. Any idea what it came out of or anyone know the specs on this motor. Thanks for any help or a link I find out the information. Rumple69, you...
  12. R

    Help with pistons

    Help, just screwed up one of my TRW forged pistons (stock). Anyone in the Phoenix area have one laying around from a rebuild? Thanks for your help. Rumple :(
  13. R

    67 coupe parts for sale

    Holy &(*^!! My bad, thought this was the place. So much angst!
  14. R

    67 coupe parts for sale

    GONE!
  15. R

    302 engine swapped into a 67 coupe sixer?

    Go for the swap. I have a 67 coupe that had the I6 and 3 speed. Pulled the motor and tranny with the rearend out. Built a stroker from my 302 roller out of my 89 5.0 and got nearly 400 ponies. Picked up a used C4 from the paper and did the rebuild with a shift kit and little worries. The...
  16. R

    WTB and %.0 Parts for sale

    WTB and Parts for sale 1. I have stock valve covers, oil pan, heads (E7) and upper/lower intake with throttle body and mass air. Also have stock headers, all from my 89 5.0 Let me know what you need best offer on all parts. 2. Bassanni X Pipe w/Cats for 99 and up 4.6 GT/5 Spd $499 new...
Top Bottom
Back
Forums
Menu