Search results

Like title says, 75 mm professional products throttle body and elbow for sale. 130 shipped obo. email [email protected] for pics

I am kicking around the idea of doing a efi conversion on my 79 stang. what is involved to make this swap work, like what parts i need besides the fuel injection stuff and mass air harness and how would it wire up to my stock 79 ignition. any help would b greatly appericated. Jhery

Ight jus found out that my flywheel is too damn big for the stock t5 bellhousing, my question is can i use a stock diameter flywheel with a 10.5 inch clutch set up?? Any info will b greatly appericated. Thanks Jhery

ight i went to install the T5 swap in my 79 hatchback, i put the flywheel on and as im about to put on the pressure plate, the bolt holes dont match up at all. I measured the flywheel and its 14 inch across and i measured the pressure plate and its 10.5. also the flywheel is 28 0z balance for my...

I have a 1979 mustang with a rebuilt 302 with 40k on it. My question is what flywheel do I have to use? I been told by a few sources that I need a 157T 28 0z balance flywheel. I just want to know if this is correct or not. Also I have a ford racing 50 oz flywheel that have 10k it if anyone...

I was wondering is it possible to put 1970 351 cleveland 4v heads on a 1979 302 block? Like what kinda of mods are going to be need done to make the head work. Thanks Jhery

I have a set of Mickey Thompson Sportman pros that measure 26x10.50-15. I was wondering do I need special backspacing to work on my 1979 stang. Also would I need the lip to be rolled? Thanks Jhery

I'm about to purchase a 87 Gt with supposely 76k on it and I want to make sure that its the right mileage. 1FABP42E9HF185653. I would reall apperciate if one of you guys can do this for me. Thanks alot Jhery

I was wonder if anyone would have a complete T5 set-up that they will be trading for 2 AOD's with a TCT 3200 rpm stall converter and Flexplate. One tranny is a rebuilt AOD with 10k miles on it, the other is a dynamics aod but OD is blown in it. I didnt know what section to put it in so i jus...

Click the link and tell me if any of you guys know the real name of these pipes cuz i jus call them mad max pipes. http://www.fastls1.com/forums/showthread.php?s=&postid=57568#post57568

Im about to purchase a s/c 88 mustang hatchback, here is a quick run down on the mods. it has 50 lb injectors, novi 2000, in line fuel pump, mass air conv. , 373 gears, alum driveshaft w/ loop, brand new centerforce dual friction clutch , new msd wires, dart stage 3 heads, cobra r's needs new...

I'm about to get a 8.8 rear and the seller isnt sure if it have 3.27's or 3.55's in it. Is there a way to determine what gears are in the rear when the rear is out of the car? Thanks Jhery

I have a 79 mustang with a 302 with about 40k on the engine rebuild. As far as I know, it have stock internals. My question is how much boost can I put into the engine before the pistons crank or I throw a rod? The supercharger that I plan on using now is nothing too serious, just a Holley 174...

My question is how many ft-lbs do I torque the flexplate bolts down to on my 79 302 and should I buy APR bolts or reuse the stockers? Thanks Jhery

I was wondering how hard would it to do a homemade port job on a set of E7's that I got for free? Also what is the average price to have a shop to port heads? I don't want to do anything crazy, just enough to flow a good amount of air. Thanks Jhery

I have a rebuilt 89' AOD with about 10k miles on it. From what I know the tranny is pretty much stock. I'm getting a dynamics built AOD for free that have blown OD with a TCT converter. I want to know how hard is it to change over the valvebodies so that I can have the good AOD shifting nice and...

I'm wondering how much nitrous can a stock 79' 302 take? The engine was rebuilt 40k miles ago. From what I been told, the engine is totally stock, it just had a rebuild on it. Also how much power you guys think I can make at the flywheel with ported E7 heads, 1.7 roller rockers, edelbrock...

I have a 79 stang with a rebuilt 302. The C4 trans was taken out and I have a 89 AOD to go in it. My question is what flexplate do I use with that engine and trans combo? I was told to use a 164 tooth 28.oz flexplate, is that right? Thanks Jhery

I am in need of a AOD converter so that I can put the transmission back in my stang. I would prefer a performance converter but I'll take a stocker if possible. PM me if any of you guys have one that you want to sell. Thanks Jhery

I am wondering how much power can a 1970 351 4 main bolt block can take because I plan on running maybe 10-12 pounds of boost and hoping like 650-700 hp. Considering that I will be doing a bullet proof rotating assembly with forged everything and splayed main caps also. Do you guys think that...