Search results

Just wanted to share this with you guys cause I know there were a couple of you interested in dying fabric. I decided to keep my rear seats instead of doing a RSD and needed them to match my front seats (silver/black corbeaus) better. I came across Dupli Color's Vinyl and Fabric Dye and...

My team finally did it and I'm 3000 miles away...hopefully southwest will have some cheap airfare to fly me home for the weekend parade. And yeah there were some bad calls by the umps, but they went both ways...

Not because I don't know how to but because as soon as I get on the brakes after dumping the clutch the tires stop spinning. It's like the rear brakes are locking or overpowering. Is it possible that maybe my proportioning valve is screwed up and sending too much pressure to the rear brakes...

I just moved to Sacramento last Sunday and with football season just about to start (pre-season doesn't count) I need to figure out a way to watch the Eagles and Penn State. My brother in law got the slingbox when he moved to RI last year but he never hooked it up. Is anyone using a Slingbox...

I didn't know these were out yet, but on my way back from the airport I almost crashed tryin to get a pic. I tried to get more but he got off the highway as soon as I caught to him....

Yesterday I was under the car switching back to a rubber trans mount and doing a normal under car inspection, and noticed that with the front tires raised and the rear tires on the ground, I can rotate the driveshaft about a 1/2" either way. No side to side or up and down movement, just...

I just got Summit's 7" x 24" starter shield wrap and I'm just wondering what's gonna happen if it makes direct contact with my header? I don't want the thing to catch fire or melt onto my starter. I'm going to unbolt my pass header today to do some clearancing to the scatter shield so I'll try...

For you guys that have the 13" Baer rear brakes have any of tried to run a 16" wheel out back? I believe the instructions say you need a 17" wheel, but if I could fit like a 16" pony wheel I'd rather do that for track wheels. I have a pair of 17" in my living room that I was going to mount...

My stock rack is junk so I need a new one and I'm just wondering if anyone has had luck with a certain remanufactured rack. My steering rack is loose and I want my steering to be tight just like it was when it was new. I've heard some bad things about AGR racks but I haven't ruled them out...

I got the old K Memer out and the new PA Racing one in with no problem, but the motor mount locating tabs aren't lining up. I've heard some other companies require that the tabs be grinded off, so should I grind mine off. Also, how did you guys square the K member to the frame? Maximum...

I bought a 6pt MM roll bar from a guy in jersey almost two years ago and I finally started to work on it. The bar is for a coupe and I need to make it fit into my vert, so I need to shorten the main hoop by at least 2". I'm also going to have a tonneau cover over the rear seat so the rear bars...

Saturday I removed my front Pro-Kit springs and was ready to cut a 1/2 coil off, throw them back in there and call it a day. At the same time I removed my stock steering rack to put in my new Flaming Rack power rack but now I'm stopped because my Steeda bumpsteer kit won't thread onto the FR...

I got my old rack off yesterday and I went to transfer my Steeda bumpsteer kit over to my Flaming River power rack and the threading on the inner tie rods is different. Do Flaming River racks use a different thread size on the inner tie rods or did the previous owner of the rack switch them...

I just pulled out my driver side Eibach Pro-Kit spring and was about to just cut a 1/2 coil off and throw it back in and I got to thinking...I shoud just switch to a coil over set-up? I already have Bilstein struts, so should I get the Maximum Motorsport conversion kit, or should I try and...

The UPS guy just dropped off this today... It's a Flaming River quick ratio power rack and the guy I got it from says it's got 9000 miles on it. Visually it looks fine, but is there anything I can check before I install it? I might not be able to put it in for a couple weeks. And...

I just got offered a promotion to a plant in Pinellas Park, FL and would be moving into the Tampa area. I'd most likely live in Clearwater. Anyone live near there? What's there to do? Is it a good place for people in there 20's. Just any feedback on the area would be appreciated...

I'll hopefully be picking one up this week, but I just wanted to find out what the advantages, if any, are over a stock replacement. My stock rack has a lot of play in it and it's somewhat dangerous at highway speed.

I have a ticking/tapping sound that I have determined to be coming from the fuel injectors (30lbers). I put a two foot wooden dowel up to my ear and touched each fuel injector. Some are louder than others. Is this normal? If not, what causes it and will it cause any serious problems if I...

I'm looking to remove the lower front spring isolators without having to unbolt eveything and break the ball joints loose. Would it be possible, with the car jacked up, to put a spring compressor on the spring and compress it enough to remove the isolators? I'm just trying to drop the front a...

My seats have faded from gray to a purple color, so I need to either recover them or dye them. I was considering getting new covers from Corbeau but they're $250 and recovering is a PITA (I did it once already). Has anyone dyed cloth with good results? I'd be looking to go black. Thanks