Search results

  1. BennyBlown2v

    1987 5.0 5pd Coupe $4500

    isting my custom painted blue '87, 5spd, for sale. I am getting rid of this since my dad and I are building another car and I don't have the time or money right now to continue playing with this car. I have done an extended tear down and rebuild *HERE* of most of the mechanical systems and...
  2. BennyBlown2v

    how long have you had your car and how much have you spent?

    I've had my 87 since last Sept/October and have put about $1500 into it, so about $4500 total.
  3. BennyBlown2v

    Turn signal issues! '87 5.0 swap

    Does anybody have a diagram/photo of the pinout for a 90-93 multifunction switch??? I just need the top connector pinout, that's the one that deals with the signal wires.
  4. BennyBlown2v

    Turn signal issues! '87 5.0 swap

    FIGURED OUT THE TURN SIGNALS! Both of the switches I have are 90-93 signal stalks (including the one that came with this car)...the ONLY wiring difference between 87-89 and 90-93 at the multifunction switch is the pin out for the signals lol... Basically, the pins are in the wrong place in...
  5. BennyBlown2v

    Turn signal issues! '87 5.0 swap

    Good point! I'll check the wires on all the plugs. Dash harness should be grounded, me and a buddy went through all the grounds we could find and made sure they were solid. And yes, the flasher unit I replaced was the right one lol...under the dash behind the radio, light blue and purple/pink...
  6. BennyBlown2v

    Turn signal issues! '87 5.0 swap

    Yeah I've gone through all of that except the ignition switch...and I don't know if my MF switch is right or not because I'm not sure what dash harness is REALLY in this car LOL. I know the connectors are the same, but I heard the wiring pin outs are not. I might as well put a new ignition...
  7. BennyBlown2v

    Electric Fan Install

    What they said! Just move that T to the heater core inlet and put your aux temp sensor in there. :)
  8. BennyBlown2v

    Rear end rebuild checklist

    Because the caliper bracket should hold the caliper and rotor on in case of an axle break. But it's still a good idea, especially if you want to run 33 spline axles or anything bigger than 31's. Honestly I would just run 31 spline c-clip axles and save the money on the whole thing. It takes a...
  9. BennyBlown2v

    Now my blinkers! WTF

    I would think it's a bad multifunction switch. I had this same issue on a Jeep where the switch had broken internally
  10. BennyBlown2v

    Turn signal issues! '87 5.0 swap

    Just tried signal on with the hazards, no change. Also, my hazard flashers are only in the inner lights in the front and back - are they supposed to be in the corner lights too on these cars or what?
  11. BennyBlown2v

    Turn signal issues! '87 5.0 swap

    Hey guys, here's the break down of my car: 1987 2.3l car 5.0 swapped Previous owner says it has a 91 engine/dash harness A9l 1993 multifunction switch The issue: I'm restoring this car and dealing with all sorts of electrical issues - all of which I have figured out EXCEPT the turn...
  12. BennyBlown2v

    What am I doing wrong (dragstrip question)

    Rev it out! Think about it this way - when you reach the end of a gear if you shift too early you'll end up being at an RPM in the next gear making less power than if you let it rev yo :nice:
  13. BennyBlown2v

    Are these S197 seats?

    No. I like these seats. Thanks :nice:
  14. BennyBlown2v

    Are these S197 seats?

    Yeah I looked at local JY's, no 05+ cars at the moment :( People just don't wreck enough of those damn things I guess LOL!
  15. BennyBlown2v

    Are these S197 seats?

    I think you missed the part where I don't have any headrests :rlaugh: I'm trying to see what other ones fit because nobody on ebay/craigslist has any 05+ mustang headrests for sale :nice:
  16. BennyBlown2v

    Are these S197 seats?

    I would really appreciate it, actually :) I checked with 08 Escape seats in my moms Hybrid and they are too narrow :rolleyes:
  17. BennyBlown2v

    Are these S197 seats?

    Uhh, what? 33lbs is pretty light for a reclining seat! A leather/power seat is 50-55lbs or more. So edge headrests fit for sure??? Thanks for all the help guys :hail2:
  18. BennyBlown2v

    Are these S197 seats?

    Tha'ts what I thought too, thanks man! I've been looking for headrests but can't find any used locally or on ebay :( Hopefully I find some by the time I get my harnesses haha...
  19. BennyBlown2v

    Are these S197 seats?

    Hey guys, I just bought an 87 notch with a buncha weird parts in it, and can't figure out these seats! :rlaugh: They obviously have other rails on them, but I think they are 2005+ v6 cloth seats??? The reason i need to know is so I can get some headrests, apparently the ones that were in...
  20. BennyBlown2v

    2009 IndyHP Street Car Shootout!!! Indianapolis, IN - July 5th@O'Reilly Raceway Park

    Bump! Only a few days till the shootout, hope to see some Stangnetter's there :nice: