Search results

I was poking around in a wrecking yard today and found a 94 GT with a white face gauge package with a 160 mph speedometer. I know this is not stock and I'm wondering what this gauge unit would have come out of. Cobra, Saleen??

I forgot to mention that we are looking at staying with the stock gt cam but going with 1.7 rockers.

Approximately how much hp gain would a mildly ported set of GT40 iron heads with the GT40 u/l manifold, 65mm Tb and 24# injectors and matching MAF give to a stock 95 gt? We are going to stay with the stock gt cam but change the rockers to 1.7's.

My 95 GT makes a howling/whining noise when it shiftes into overdrive. I had to take my aluminum driveshaft out because it seemed to amplify the noise. If you take the car out of overdrive, the noise stops. I had 2 trans shops ride in the car and both of them said it sounded like the bearing on...

Legendary Pro Stock Mopar driver Ronnie Sox passed April 22 from pancreatic cancer. I remember seeing him drive at a lot of national events. NOBODY could shift a car like he could. Sox & Martin, Gapp & Roush, Bob Glidden, Lee Shepard these were some of the key players in making Pro Stock racing...

dex-cool I just went out and looked at a jug of the Prestone Dex-cool. It says it is approved for all gm vehicles that need dex cool. It is approved for all light duty trucks and cars that have "aluminum" radiatiors. It is compatible with certain Ford antifreezes and Daimler Chrysler also, but...

e303 cam Ford racing says to install this cam 4deg advanced. It is also a 1.6 ratio rocker cam. They did not recommend using 1.7's when I talked to them.

manifold A for sure way to find out what the manifold fits would be to take all of the numbers & info off of the manifold and call offenhauser or try punching the info in on Summits website. I have solved several problems with id's on parts using Summits website. Look on the bottom of the...

Anybody know anything about a place called the "Throttle Stop"? It is supposed to be in Roseville I believe.

Looking for recomendations for tune shops in norther california. Not bay area, but up the i5 corridor from Sac to the oregon border.

bargain $1065.03 to northern cal. and thats not even to the coast.

mom & pop This is a 95 cobra. The heads are iron gt40's, 24# injectors, gt40 intake,80mm pro m maf, 70mm tb,K&n filter with silencer removed. JBA headers, h pipe, 2.5" exhaust, 5 spd, 410 gears. Compression ratio will be around 10:1. MSD ignition. As far as pics go, lets see $800+ for a good...

We got the block and rotating assy back this week. Just had to break the glaze on the cylinders and we had the rotating assy balanced. We got forged pistons and rods for the beast. Got a new oil pump and all the usual bottom end stuff. Had the crank journals polished. We had the heads cleaned...

Edelbrock heads The edelbrocks on my chevy picked it up quite a bit. I did put the whole kit in the engine though. Rpm cam/intake and 800cfm carb. It put out 540hp on the dyno when we broke it in which is what edelbrock advertises and that was at 5400 feet in Denver. At sealevel where I am now...

edelbrock heads The easy way to find out would be to call edelbrock tech line and ask how to tell the difference. They can probably tell you what that "EO" number applies to. The rpm heads are just a non emissions version of the performer heads. I have the performer heads on my bb chevy in my...

copper gaskets I bought the copper gaskets for my Nova and they leaked like a sieve. I pulled them off a couple of times, cleaned everything up and still they leaked. The heads are Dart and the headers are super comp hooker. I finally got them to stop by buying "Byson" exhaust gaskets. they are...

car is a dog Per Ford racing, the e303 cam is a 1.6 ratio rocker cam shaft. That would be where I would start and get that part back in spec. Ford racing says to install that cam 4deg advanced. You need to get a few miles on the engine. It needs time for all the bearings etc to get run in. It...

injector colors orange-19#, light blue-24#,red-30#, Dark blue-36#,green-42#

Steeda subframe connectors The Steeda kit does come with the cross braces that bolt to the seats. They come in bare steel part #555-5245 or zinc plated part #555-5246. I put the zinc plated ones on mine. It took the shop about 1 1/2 hours to do the job. They also come with a plate for the...

Has anyone been having trouble getting onto the board here? For about the past week, my response has been getting slower and slower when I'm on here. I keep getting "server cannot be found messages" just when moving from one item to another. I am having the same problem on one other site, but...