Search results

I'll remember that the next time I'm pulling my 40 foot sea ray with my mustang. The car will rust to pieces before any weakness is exposed if the damage is deemed repairable.

You seem to contradict yourself a bit here. It will drive differently but you won't notice or feel it? Might want to re-think that. My car was hit and sustained similar front end damage when it was a few months old. I took it to a good shop and the car has no problems at all. Whether it...

+1 for blizzak or any snow tire. I've got dunlops now just because I bought them from a guy who used them for a season then sold his GT. I don't even have any weight in the trunk and have no problem getting around, the tires just dig in after a few revolutions and bite really well. Just...

Thanks for all the replies. So per that link that was posted you need to take the axles out to just replace the trac lok? I'm not looking at adding too much horsepower down the road so leaving everything stock is fine with me.

Does anyone know of a write up anywhere on replacing the clutching inside the limited slip? Mine is starting to get loose and I'd like to do it myself but haven't found any good write ups anywhere to make sure I can do it myself. I've searched and found some info but no detailed steps. I was...

It's time for new shocks on the GT and after searching the forums I think the Mach or bullit shock/strut and spring kit is for me. Could someone point me to th best place to by this from? Some of the posts from a while ago had some very low prices which I can seem to find anywhere. Thanks for...

yeah, our cars take a long time to warm up. I just drive the car to the train station in the morning which is maybe 10 minutes at the most. Even when i let it warm up for 5 minutes it take until I get there for warm air to make it out. With heated seats I would just give it a 1 minute or so...

The place I'm leaning toward is autowarm.com. There are also a few other places that can be found doing google searches. Does anyone have any experience taking leather seat covers off of our seats? From what I've found it's pretty simple to do once you get the seats out of the car. I'm...

As winter approaching in Chicago I'm dreading sitting on the ice cold leather seats in the GT first thing in the morning. I've been looking at some aftermarket heated seat kits to use, only about $80 per seat. Has anyone ever used or done anything like this?

I went to NTB last time for my alignment and they offer a 1 year, 3, and 5 year free alignment plan. http://ntb.com/Alignment.aspx can't remember the exact cost but I think the 5 year was $150 or something close to that.

Hi There's a thread in tech right now where a guy added the spacer between the intake and throttle body and said that it stopped the hanging idle issue with our cars that Ford programmed in. Has anyone else experienced the same thing? If so I might need to order one. Thanks...

Could someone point me to a place where I could find this spacer? Did it make a big difference? Thanks

Not to hijack the thread but what is the 1/2" spacer you installed? Was that to fix the hanging rpms between shifts with the stock setup? I've heard of and tried both the copper pipe mod and the sheet metal between the IAC and intake mod but have never seen a 1/2" spacer. Thanks

I think I was the one who posted on it a week or two ago. I meant to post pics but the camera isn't working correctly so that didn't happen. The bolts were tight and it still rattled. I just pried the plate back a bit by the notch in the tranny and shoved a 2x2 inch piece of rubber gasket...

Does anyone know if the extended ford 75,000 mile warranty covers this?

I'll get some pics either tonight up tomorrow when I get home. Once you see those you'll immediately see what I am talking about. I could even make it rattle with the engine off just tapping it with a screwdriver

Hi everyone, I've seen a bunch of threads on here pertaining to a rattle that sounds like marbles in a tin can and starts around 2-3k rpms. I thought it was the cats at first and so did the dealer so they replaced the entire mid pipe, however the rattle was still there. If finally pissed...

I had to do mine a few months ago, it was a breeze and no rivets at all like everyone else said.

You should look at Zaino Clear seal. It's new on the market and supposed to last 9 months with just one coat. You just apply it and then walk away, there is no waiting for it to haze and then removing it. It's expensive but you use so little that the bottle will last forever. It's also so...

Makes sense, thanks for clearing that up