Search results

Ok guys, Just got done rebuilding my C4. Got everything put in and started it up and it sounded like the engine was loading up. Gave it a little gas while in park and the car moved forward. Same with reverse. In all the gears there is only drive. I do not get 1st, or 2nd. When i tried...

Its a holley 4160 600cfm vac secondaries, electric choke. Its sitting on a bored 302. I just put a refresh kit in it. So i know everything is clean and in working order. I have searched this topic, but nothing has helped me with my problem. Here is what happened, when pulling it apart...

Does anyone know where to get the best c4 auto manual at. I have been looking but i haven't been able to find anything that will be real promising.

Just got the car running today and did the break in. After i broke it in i decided to take a test drive. When i went to put it in gear it didn't move. I checked the tranny fluid(C4). It was a little low. Added fluid, then when i put in reverse it wanted to lunge forward. And take off. I also...

Please please help Engine/Trans problem Just got the car running today and did the break in. After i broke it in i decided to take a test drive. When i went to put it in gear it didn't move. I checked the tranny fluid(C4). It was a little low. Added fluid, then when i put in reverse it...

I just recently have had my motor rebuilt 69' 302. It originally had a three bolt dampner on it. They installed a new dampner, but it is a four bolt. I have spent almost two months looking for the right pulleys, and i can't afford the march pulley setup. Because i couldn't afford to have the...

I am leaning towards this quite a bit.. I had it done and now i have the software and i am going to tinker with it a bit more. Let me know any ideas or thoughts... I know it is far from the usual mustang paint job but i like it.

Does the vacuum line from the trans plug into the back of the intake manifold. I have a Edelbrock Torker I, It has one plug in the back that is tucked just below the carb. Also what do you guys recomend for initial timing. 302 Bored .30 over, all accel 300+ ign, hooker comp headers...

Would someone please do this. I posted it in the virtual body shop and no one did it. i am wanting to get away from the norm with just a plain color and stripes. i want a two tone that either follows the body line, or is split just in front of the rear tire with a tear/rip whatever you can come...

Just got my engine back and everything went smooth until i had to put the pulleys on. Thats when i noticed that when they rebuilt it they put a new balancer on and switched from my 3 bolt balancer to a 4 bolt balancer. I spent 2 1/2 days looking for pulleys. I finally found a pair that fit...

has anyone redone their fuel line with the rolls that come from summit? How hard is it to unroll it, or is it even worth the time? i know that their are prefabbed lines, but budget is still a lil tight and i can save some money this way, if its worth it.

if it is how hard waould it be to swap it into the red car? and how hard would it be to find the parts for it, pulley, pump, bracket? http://www.cardomain.com/ride/2127430 This set up is in the grey car in the background, the red car does not have it. If anyone knows prices to that...

i need to know. PAW has the hooker comp for 158.98. is there any preference in that price range.

i want to use an extra volume oil pan for my 302. summit has a milodon and moroso 8 qt pan, front sump. they are moroso 169.98 8 3/4" deep & milodon 179.88 10". do i need to order a new pick up tube as well or will the stock one work.? what do you guys prefer. if you know of anywhere...

building my first v-8 in my 69 coupe. 306 block re-worked heads (oversized valves, roller rockers, new springs) Cam is still undecided. edelbrock torker II intake ( hope its not to much for the 306) holley 650 cfm double pumper accel 300+ ignition and coil accel distributor(need to...

what are the benefits of a windage tray.??? is it worth spending the money to intall one. I want to use one on my 69 coupe with a 306. I will be doing some drag racing and open road racing.

hey guys, i was thinking about fabricating a cold air intake set up for my 69 carbed 302.. i know on my toyo truck it helped out quite abit with breathablility. but that is efi. how well will it work for carb setup???? it will most likely run down by the front valance. how would...

hey peeps, what is the biggest size radiator that you can fit in a 69 coupe. have a good deal on a 31x19 aluminum radiator. could i make it fit???

i am building my 306, but am not sure of what size carb to use. I have tested the calculators out there and they give me a 450cfm, but all the guys at work tell me that it is too small. I will have .10/.10 under crank, hyper pistons, ported and polished heads with roller rockers & racier...