Search results

I'm selling my 17.5v KB 40 amp BAP for supercharged/turbocharged engines (comes with hobbs boost switch and controller) part number KB89069. Fits any car. Dayton OH. $190 shipped.

Rears: 15x10 Racestars with 19mm offest/6.25 inch backspace and 26x10 stiff wall MT ET Drags. Fronts: 17x4.5 Racestars with 1.75 inch back spacing and 26x4.5 MH Front Runners. Fits perfectly over 96-04 cobra brakes. The fronts are direct drill but the rears are not. I have cut 1.46 60 ft...

This is a set of 4 Silver Enkei RPF1 Wheels 17x10 +18 offset 5x114.3. They are in excellent condition. They are 2 years old and were only used in the summer on weekends for autocross. These weigh only 17.25 lbs each! $650 for the set. Local pickup in Dayton-Cincinnati OH area or will ship at...

For sale is a set of Manley stroker pistons and rods. Pistons are custom SHM made by Manley. Pistons are 0.020 over, 28cc dish, and forged 2618 Alloy. Compression ratio would be 9.4:1 with 38 cc heads, 9:1 with 42 cc heads, and 8.8:1 with 44 cc heads. Rods are forged 4340 and 5.828 inches in...

For sale is a pair of stage II ported PI heads (romeo valve cover bolt pattern). Heads flow 218 cfm intake and 193 cfm exhaust. Intake valve is 1.78" and exhaust valve is 1.452". Bronze guides. 46 cc combustion chambers. 0.600" lift springs. 5 angle valve job. Stainless Steel Valves. Will fit...

For sale is a set of stock 96 cobra flat top pistons and rods in great shape. Engine had 90k miles at tear down. Ready for install with new bearings and rings. located in cincinnati oh. Looking for $90 shipped.

ARP 156-5401 8740 main studs. Fits all 4.6L / 5.4L Iron Blocks without a Factory Windage Tray, including the Boss 5.0L Block. Studs are in perfect shape and were only used once. $60 shipped.

$25 shipped. New 4.6l 2v straight chain guides from ford.

These DW300 fuel pumps are very high quality pumps. They are e-85 compatible and flow 320 lph at 40 psi. See attached links below for more flow and electrical spec info. They fit just the same as walbro and stryker pumps. These were only used for a year. The full install kits are included...

These two 340 lph Stryker fuel pumps were used for just a few months. All parts are included except one pump needs a new filter. Selling the pair for $200 shipped. Each Pump Includes: Fuel Pump (Offset Inlet-Inline) (2) High Pressure Hose Clamps Wiring Pigtail Submersible Fuel Hose Fuel Pump...

These eibach wheel spacers are in perfect condition. These are hub centric and bolt on to your existing hubs so that your wheels can be bolted on spaced out 25 mm (1 inch). Selling the pair for $100 shipped. Located in Dayton Ohio...

This is a 40 amp KB BAP (single 17.5 volt) part number KB89069 for supercharged and turbocharged cars. Includes install kit. Selling for $140 shipped. Boost-A-Pump

Two polished Race Star wheels 15 x 3.75 with MT ET front tires 26 x 4.5 x 15 in excellent condition with lots of tread left. Includes lugs, washers, and wrench for hub caps. Selling for $350. Would prefer local pick up near Dayton-Cincinnati Ohio area but will consider shipping.

These are Steeda underdrive pulleys for 1996-mid 2001 4.6L GT engines with the long water pumps. These are a few years old but are in perfect working condition with no degradation of the elastomer on the harmonic dampener. Includes alternator pulley, water pump pulley, and harmonic dampener...

For sale is a pair of Maximum Motorsports non-offset urethane bushing control arms part number MMFCA-7. Arms were only used for a year and are in perfect condition. Price is $250 shipped to lower 48. http://www.maximummotorsports.com/Non-offset-Front-Control-Arms-1994-04-Mustang-Urethane-P393.aspx

OK, so I finally went to the track last night with the new blower among many other new mods and had a blast. I've been wanting to go since I moved to Utah but just haven't gotten around to it until now. I haven't been to the track in about 5 years so I figured I would be a bit rusty and I...

New KB 2.1L Inlet with Oval TB for 2v GT- 600rwhp @ 20psi Sheet metal inlet for 2.1L KB 2v - ModularFords.com Has anyone tried this? Is this the only inlet out there for the 2.1 on 2v cars? The price and performance look pretty sweet.

What cams would be best for my setup (in signature)? I don't want to rev past 6k rpm... What kind of gain can I expect over my Comp XE268H cams? http://www.compcams.com/Cam_Specs/CamDetails.aspx?csid=966&sb=2 Right now I'm thinking about MHS Stage 3 blower Cams...

Currently considering Corbeau FX1 Pro seats in microsuede. Corbeau: FX1 Pro I like the price and weight of these seats a lot. They look like they would provide a ton of support too. Anyone ever see their microsuede seats? What is the quality like? I'm 5'7" and worry they might sit too low...

I've decided that I'm going to make this happen one way or another but I will need help figuring out what mods are needed for it to work. The M-9002-C46 Cobra tank is baffled and comes with the dual pump and hat assembly. Ford Racing Fuel Tanks on special at BrothersPerformance.com Price...