I found a 2.3 pinto header will it work for a mustang application?

Discussion in '2.3L (N/A & Turbo)' started by T3AL, Oct 19, 2004.

  1. T3AL New Member

    Member Since:
    Oct 17, 2004
    Message Count:
    216
    Likes Received:
    0
    Trophy Points:
    0
    and are there any aftermarket duel coil packs for the 91-93 na 2.3?

    ????
    T3AL, Oct 19, 2004
    #1

  2. Red_LX Doubt I could be of much help, unless you need por

    Member Since:
    Aug 21, 1998
    Message Count:
    10,471
    Likes Received:
    2
    Trophy Points:
    78
    Probably not.
    Red_LX, Oct 19, 2004
    #2

  3. mr_woodster New Member

    Member Since:
    Jul 28, 2003
    Message Count:
    1,316
    Likes Received:
    0
    Trophy Points:
    0
    Dpstang is selling a longtube that would fit (long tube makes the most hp)...believe he's selling it cheap. Coil packs? chances are , no.
    mr_woodster, Oct 19, 2004
    #3

  4. T3AL New Member

    Member Since:
    Oct 17, 2004
    Message Count:
    216
    Likes Received:
    0
    Trophy Points:
    0
    damn, to bad I couldent fab two coil packs from say a 4.6....
    T3AL, Oct 19, 2004
    #4

  5. HIGDON New Member

    Member Since:
    Nov 2, 2003
    Message Count:
    243
    Likes Received:
    0
    Trophy Points:
    0
    DUAL, it's DUAL ahhhhhhhhhhh
    HIGDON, Oct 20, 2004
    #5

  6. freakintiger New Member

    Member Since:
    Apr 9, 2004
    Message Count:
    310
    Likes Received:
    0
    Trophy Points:
    0
    You can use the Accel and MSD coil packs , the listing is the same, when I get the bucks I'm going to get a pair of MSDs from Summit, cheapest source I can find. The ones listed on eBay are more expensive because Summit doesn't charge for shipping(just an $8 handling fee).
    freakintiger, Oct 20, 2004
    #6

  7. T3AL New Member

    Member Since:
    Oct 17, 2004
    Message Count:
    216
    Likes Received:
    0
    Trophy Points:
    0
    are you talking about the dual coil setup?
    T3AL, Oct 20, 2004
    #7

  8. TurboFlush Founding Member

    Member Since:
    Dec 8, 1999
    Message Count:
    1,984
    Likes Received:
    0
    Trophy Points:
    0
    depends on what pinto it is. from what I remember they had both the 2.3 (lima) and the 2.0 (pinto) block in the pinto's.
    the two are incompatable though. look the same, but not.
    TurboFlush, Oct 20, 2004
    #8

  9. T3AL New Member

    Member Since:
    Oct 17, 2004
    Message Count:
    216
    Likes Received:
    0
    Trophy Points:
    0
    It just says 2.3 pinto :shrug:
    T3AL, Oct 20, 2004
    #9

  10. HIGDON New Member

    Member Since:
    Nov 2, 2003
    Message Count:
    243
    Likes Received:
    0
    Trophy Points:
    0
    Call them and ask?
    HIGDON, Oct 20, 2004
    #10

Share This Page