99FiveOh
10 Year Member
Correct, except the sender usually goes on the driver side and ECT goes into the passenger side near the thermostat housing.
Build Thread Jamee's Build Up Thread
- Thread starter Jamee
- Start date
-
Sponsors (?)
Adam95GT
New Member
The ect goes in the heater tube usually. the one for the gauge goes in the lower drivers side of the intake
sorry, if I've only edited stuff out that wasn't necessary, as for pictures, my server's drives messed up and lost some stuff, I've put as many pictures back as I could from backups but something may be missing. I try not to edit things so people don't get confused tho. I've been working on other projects currently, and finally got around to fixing my daily driver's alignment issues but still need to replace the cv shaft and such.... I'll keep updating as progress continues.
Oh, I missed something. I replaced the taillights and put in different ones. Here's a pic. Car is nappy looking from not being washed.
wheel flew off going 70, damage is minimal, thank god
Finally got the proper throttle bracket and modified it to be used, will post pics after I get the correct upper and lower gasket so I can mount the upper intake
Finally got the proper throttle bracket and modified it to be used, will post pics after I get the correct upper and lower gasket so I can mount the upper intake
Black95GTS
Active Member
Thank god you are safe!
I flew into the airport in Flint a bunch of times, its TINY, and they don't serve beer.
I enjoy this thread, keep it goin!
Adam
99FiveOh
10 Year Member
Meh, Chrysler.. nuff said!
Keep the updates coming, with any luck you'll have this thing running by the end of the year! We're pulling for ya!
Keep the updates coming, with any luck you'll have this thing running by the end of the year! We're pulling for ya!
it'll be done by then. It's going much slower than I thought it would, but doing it right takes time 
Know where I can get the plastic "quick connect" from this pic? I don't want to have to cut the end of my fuel line off to put another one on there
Know where I can get the plastic "quick connect" from this pic? I don't want to have to cut the end of my fuel line off to put another one on there
Thank god you are safe!
I flew into the airport in Flint a bunch of times, its TINY, and they don't serve beer.
I enjoy this thread, keep it goin!
Adam
I like flint's aiport, it's not that bad!
it'll be done by then. It's going much slower than I thought it would, but doing it right takes time
Know where I can get the plastic "quick connect" from this pic? I don't want to have to cut the end of my fuel line off to put another one on there
SableSal
Member
it'll be done by then. It's going much slower than I thought it would, but doing it right takes time
Know where I can get the plastic "quick connect" from this pic? I don't want to have to cut the end of my fuel line off to put another one on there
Autozone
Labora
Founding Member
I just had a similar fuel clip headache.
Best two options are go to parts store and have them open a book and order you what you need. I know most parts stores don't realize that they can get stuff outside of the computer!
Or check this site.
Ron Morris Performance: Stock Ford EFI Fuel Fittings & Fuel Line
Best two options are go to parts store and have them open a book and order you what you need. I know most parts stores don't realize that they can get stuff outside of the computer!
Or check this site.
Ron Morris Performance: Stock Ford EFI Fuel Fittings & Fuel Line
Trying to finish up some of the last few things. I have a T4M0 (auto) computer. Trying to buy a t5 computer cheap, or I could switch to an 89 MAS computer (A9P, A9L, and repin to work, but would require seperate radiator fan controller) or I could get a Quarterhorse ($250) T4M0 chip and just change it to work for the T5. Again, trying to keep things on a budget so when I move I'm not broke... Any opinions on what I should do? I greatly appreciate your 2 cents 
alleymad95GT
Member
apparently the computer pulls the timing harshly on the 94-95's AODE when the computer sees the AODE needs to shift, so it does need to be replaced with a manual ecm, or chipped to alter the auto settings :-/
Similar threads
