Search results

  1. Tally_4.6

    VSS problem with a CEL

    This problem has been going on for quite some time, so i'd figure i'd do something about it and stop being lazy. Over 2 years ago my CEL came on and it turned out to be the VSS p500 code. So i replaced the sensor with a Motorcraft and the speedo gear with a white one from Steeda due to me having...
  2. Tally_4.6

    Hood cowl replacement?

    I pretty much destroyed my hood cowl yesterday taking it off. My Q is would it be easier putting it back on with the hood off? I have no problem removing those 4 bolts and the hood if it means an easier installation and this new one not breaking. I'm prolly gonna order it off 5.0 resto for...
  3. Tally_4.6

    New clutch cable time?

    My car has been down for quite a while now, but i had to move it a short distance at my house a few weeks ago and i couldn't get it into gear. It would almost engage, but not go all the way in. I had just gotten the tranny fixed but it's been sitting for another problem. This is what it looks...
  4. Tally_4.6

    So i spun my balancer off today...

    Today leaving the school parking lot i got on it for a second and right as i let off i see what looks like a pulley shoot out from under my car and into the grass. It shocked me for a minute but i didn't hear any weird noises or my car do anything funny so i naturally thought it was sitting in...
  5. Tally_4.6

    Rear main seal question?

    So i dropped the tranny to get it fixed and figured while i'm at it i might as well replace the main seal and pilot bearing. I read up on all data and it said to remove the seal retainer plate if necessary when replacing the seal. So i did it w/o removing it, and pulled the seal out...only to...
  6. Tally_4.6

    Blown trans??

    This might be a little lengthy, sorry. Ok so today i had a little incident. Going to lunch today i pulled out on the street in 1st gear and got on it a little, shifting into 2nd it grinded for a sec then nothing and the rpms went up. Thinking i missed 2nd i tried again and nothing, shifter...
  7. Tally_4.6

    Front bumper removal help

    I'm taking off my front bumper and can't for the life of me get those 2 ****ing tabs on each side below the headlight pushed down, that's the only thing thats holding me back right now. All other screws have been removed, also i broke those 2 rivets at the top next to each headlight. Will a...
  8. Tally_4.6

    Hood blanket/ground strap Q??

    Ok today i was messing around with my car under the hood, and figured i would once and for all take off my hood blanket since its pretty nasty and ugly. In doing so one of the clips holds a metal ring to the blanket which follows a ground strap to the hinge. I looked in my Chiltons, figured it...
  9. Tally_4.6

    Rear defroster problem

    Ok so for the past few days i noticed my rear defroster hasn't been working at all. I push the button, light comes on and nothing. Checked the fuse, it's good. Then yesterday i thought, hey maybe i should look at the connections to the lines on the window and what do ya know the drivers side one...
  10. Tally_4.6

    My 315's rub question

    Ok so both my left and right rear tires rub on the rear parking cable bracket on both sides, is there any way to remedy this or adjust the bracket? It gets annoying after every take off. Not my actual car v v v.
  11. Tally_4.6

    Coupon codes?

    Ok i'm ordering some stuff and i need to know the coupon codes for Buyfordracing.com and Blueovalindustries.com. Please tell me somebody has these, i was suprised that they offered them and have a chance to save some dough. I already tried the 2 for american muscle. Help
  12. Tally_4.6

    A chance to get gears...

    I have a buddy who works at a Lincoln Mercury dealer who also knows a tech that is seasoned when it comes to installing gears. I told him i was interested and my buddy told me the tech would install a set of 3.73's out of a Navigator 8.8 rear end with relatively low miles on the gears. So i...
  13. Tally_4.6

    Cleaned up my TB, idle issues?

    Ok yesterday when i got home from work i cleaned up my TB plate with CRC cleaner. It was pretty dirty but i got most of it i'd say, so i start it up and let it run for a few minutes, reving it up and down. Before i did this my idle was at about 600-700 rpms, now it's at about 900 rpms. Now my...
  14. Tally_4.6

    "Go" pedal stuck every now and then?

    This is the 1st time i have encountered this problem and wanted to see what you guys thought. About 2 weeks ago me and the boys went out to the local car meet. Ofcourse on the way there all of us were messin around gettin on it and stuff, well later that night on the way back the same hotroddin...
  15. Tally_4.6

    Weird misfire problem.

    Ok so yesterday i did a little work on the car, i cleaned the interior and decided to clean the engine a little. So i sprayed some Steam(degreaser) on the timing chain cover and pulley set, then a little on the front of the valve covers, PS steering resevoir and near the t-stat. When i washed it...
  16. Tally_4.6

    Finally put the Dubs on...

    After months of having them in boxes next to my tool box, they are finally on. Recent mods : '03 machined face cobra's with black cutouts and tires, ''14 shorty antenna, '99-'04 GT shiftknob(as opposed to the POS on there before). Tires : 275/40 BFG g-force sports up front, 315/35 Sumitomo...
  17. Tally_4.6

    Lugnut Q...

    I'll be putting on my new '03 cobra's soon and was wondering if i needed to spring for some chrome lugnuts? Is this really necessary, will i even be able to see the stud/lugnut?
  18. Tally_4.6

    CCRM's interchangeable?

    I'm pretty sure i've narrowed down why my A/C doesn't work and i think it's the constant control relay module(CCRM). Last yr it stopped blowing cold on a trip and i forgot about it, then a week or so ago i turned it on for the hell of it and it worked. So I've tested all my switches, low...
  19. Tally_4.6

    Look what Brown did for me...

    These were waiting for me when i got home from work. Don't think anybody in Tally has these yet, machined face '03s with black cutouts.
  20. Tally_4.6

    '94-'98 guys, rubbing tire question?

    I may come into some wheels with 17x9 (275's) and 10.5 (315's Nitto DR's). Will these rub at all, i've heard yes and no. Anyone?
Top Bottom
Back
Forums
Menu