Search results

  1. dkbanjo

    Starting issue

    I have a 91 gt and I'm have trouble starting it sometimes. When I turn the key the motor turns and turns and turns but it wont start. This lasts about 30 seconds, then it finally turns over. After it starts the idle goes up and down like waves for a few seconds and is a bit rough. Then the car...
  2. dkbanjo

    RANDOM OVERHEATING??? HELP!!!

    I have a fresh 306 longrod with only 1000 miles. I have put a new ford racing H/D radiator, new cap, bypassed the heater core (because it was leaking), a new thermostat, and I put a high volume water pump also. The wierd part is that about once a day or every other day, out of no where the temp...
  3. dkbanjo

    loss of boost after rebuild!!

    I recently rebuilt the engine in my 5.0. it only has a couple hundred miles on it now. The problem is that I used to have 10psi of boost@6000 and with the new set up I only get around 6 maybe 7ps. I checked all the hoses and changed the pcv valve, my only suspicion left could be the bosch bypass...
  4. dkbanjo

    boost senitive timing?

    boost sensitive timing? I was just wondering if there were any hp gains to be made with using a boost sensitive ignition like the one MSD sells for 250$, or does it just allow you to run more boost safer. I have a 306 with 10psi v1 sc, srp pistons (9.0:1), 30lbs injectors, Holly systemax...
  5. dkbanjo

    Camshaft??

    I'm in the middle of rebuilding my 91', and I was wondering if I should put a new camshaft in while the motor is out. I've looked at the e-303 because of the 50 state legal aspect, but I don't know if It will work well with a 8-10 psi centrifugal supercharger (narrow 110 lobe separation)...
  6. dkbanjo

    forged pistons?

    I am going to be doing a longblock motor exchange on my 91 5.0 for $1,200, and I was wondering if it is worth throwing in some forged pistons and moly rings for $400 more. I don't have a lot money to spend and Don't plan on going over 450hp. I do have a 10 psi supercharger, holly intake, 30lb...
  7. dkbanjo

    cam suggestions

    I'm putting together a motor for my fox as you guys know by now and thank you for past advise. Well I have most of my parts picked out but the cam seems to be the most difficult to choose because of big brother. I have a holly systemax intake, vortech v1 w/9psi , and AFR heads being made...
  8. dkbanjo

    engine block ?

    Hello, I just wanted to run my new engine combo buy you guys and see If the factory block can handle it, the dart blocks are really expensive. 331 rotating assembly 9.1-1 comp 185cc AFR's holly systemax lunati voodoo part# 61011 .549 in .565 ex vortech v-1 9 psi @ 6000...
  9. dkbanjo

    good engine setup?

    Time for a new motor but I am on a budget so I am thinking of going with m&r motors 331 shortblock cuz they are local, custom ground cam with 3000-6000 rpm range,gt40 heads and reuse my v1 supercharger 9psi and my holley systemax intake mani. Does this sound like a pretty decent setup for a...
  10. dkbanjo

    looking for 331 long block

    I recently dropped a valve in my 91, so I am in need of a long block preferably a 331. I have been looking around, M&R 's prices are good and they are local but I read allot of horror stories. If anyone has any suggestions that would be great. I will be reusing my S/C and intake plus this is a...
  11. dkbanjo

    intake manifold question

    I have a vortech supercharged 5.0 and want to get a new intake manifold. Anybody know if the holley systemax will be ok with the stock heads? If anyone has used them some reviews would be awesome. Or if you know what intake would be better for my setup let me know.
  12. dkbanjo

    intake opinions?

    Hey I am thinking of upgrading my intake on my vortech supercharged 5.0. I am looking at the trickflow streetburner, edelbrock performer or the trickflow trackheat. I have stock heads so any opinions would be very helpful. ps I wanna try and stay street legal in CA also if you have dyno numbers...
  13. dkbanjo

    HELP on AOD shift points

    Anyone have any ideas on how to change shift points on an aod. Ive been looking around for shift kits ect. I don't know what route to take. If any one has an idea I would apperichate it very much.
  14. dkbanjo

    chips???????

    I just installed a vortech V1 SC supercharger in my 91 mustang and I would like to raise my shift point in 2nd. I was looking at some chips such as the hypertech 650811.It seems that it would work. I also have heard that using a chip with this s/c kit could make it run to rich or lean. Vortech...
  15. dkbanjo

    valve body???

    I recently purchased a vortech supercharger and ITs great, but whats sucks is that like every aod owner without a mod is that I have no control of when to shift out of second. So I don't hit full boost in 2. I was wondering If anyone knew the shift pattern of the TCI-432200. or if anyone has any...
  16. dkbanjo

    vortech drive belt tension

    I just installed a V1 sc trim on my car and I have heard it is easy to bend the shaft because of an overtightened belt. If there is anyone who knows how much play there should be I would really appreciate any feedback thanks
  17. dkbanjo

    new ford racing superchargers???

    I was looking at these new ford superchargers for the 5.0 and I was wondering if anyone has had any experience with them or if you guys think they are a reliable product. any feedback would be great thank you
  18. dkbanjo

    Still running warm 215 maybe ?????

    I dont know what to do. I would be greatful for some feedback. I have a 91 mustang with 83,000 miles very clean and I've put a new aluminum radiator, water pump, hoses, cap, and 180 thermostat, 100amp alter with 3000 cfm fan and air dam. It had been running cool for awhile then my hi-6 box...
  19. dkbanjo

    engine cutout & stalling?NEED HELP ASAP

    Just looking for some advice as i cant figure out what is goin on with my 5.0. When i am driving the engine cuts out and then it comes back and it stalls at idle. I have changed the o2 sensors twice,new speed sensor,new maf, and a new walbro and msd coils. Any info would be awesome
Top Bottom
Back
Forums
Menu